TIG is right of course but With Dynamic Components you can do almost everything you want to do. Try opening the Dynamic Components toolbar, (view > toolbars > dynamic components) select the hand (interact tool) and click on the guy that shows up when you open Sketchup 2013 (Derrick). Then go activate view > hidden geometry and click with the interact tool again and see what happens. Insert some more Dynamic Components from the component browser. Insert some more DC's from the Google Warehouse. Search about DC's here or at Sketchup website. Try a lot, fail a lot and you'll succeed! Best regards, JQL

The resetting of your MAC's plugins folder's permissions to FULL Read/Write has been covered many times in the forums... Here's a good one http://sketchucation.com/forums/viewtopic.php?p=468689#p468689

PipeDraft, Yes, it Bugsplats before I launch anything. In fact, it Bugsplats as soon as Sketchup opens and the toolbars show up. And no, I do not have any of the quarantined plugins installed. I will try it again later and report back. Thank You, Paul

Just had a complete evaporation from using the explode command so I think there is more than meets the eye going on here. I will try the test you described on sunday when I am no longer tearing my hair out. Pain in the proverbial. V8 is the vanilla of choice now and this is going poof too so the model itself may have some gremlins in the drivers seat I suppose. Sod.

It works as TIG described for me.

@tig said: Have you got the Units of the exported dwg and then matched them in the Imported geometry - set in the Import 'Options' sub-dialog in SketchUp ? Measure something in the imported geometry using the Tapemeasure tool and see if it's the size you expect... For example, if you have jumbled up m & mm the SKP components might be 1000x or 1/1000 of the mis-sized imported geometry - thus making you think that the components are not adding but they are either so big or so small you can't see them Also check your imported geometry's origin is set NOT to be the CAD origin [again set in Options], otherwise the imported geometry could be located many miles from [0,0,0] and thereby cause graphics glitches etc in SketchUp too... Oh snap. So that's where I went wrong. Thank you so much. I rescaled my door and it automatically rescaled the building too. You were right, the components were too small.

Thanks Mr. Gaieus

Ok. I have some updates. The block shadows does not appear when I select "Standard" Print Quality under the Print Preview dialog box. Shadows appear when I select "High Definition" or "Ultrahigh Definition". Currently I am sending my print output to a Canon Pixma iX4000 on A3+ glossy Canon paper. All sketchup models with complexity of this drawing level display the shadow problems on the Core i7 PC. Simpler models goes through ok "most" times. My thoughts are, once the cpu/gpu has successfully sent the high res print output to the printer, video should not be affected on the display. They almost use different paths altogether. Most times, the block shadows are very stubborn and I could be toggling the texture faces/shadows on/off for like 10 mins before it returns to normal. I have to do this and hope it reverts back to normal. Off Shadows, switch to hidden lines face texture, then switch to shaded with textures. And repeat after trying shadow on. Included one of my older models. Just tried and voila. Printed on high definition. [image: A5hM_photo1.JPG] [image: csww_photo2.JPG]

Yes. I found it. BTW IMO the index should be as it was - in the pull down menu on the sketchucation website: Resources - Plugin Index, just below PluginStore.

Try CurviLoft or Extrusion Tools guitarlist.com has a free sub-d plugin if Artisan is not in your budget http://www.guitar-list.com/download-software/sketchup-loop-subdivision-smooth-plugin

It has happened to me many times and I found this plugin to unhide all that is very useful http://sketchucation.com/forums/viewtopic.php?t=2052 unhide_all.rb

I had a similar 'plight' with a design I was creating for a very large model of a bespoke hospitality (tensile/inflatable) structure being built on the beach at Cannes - the model was constructed in SKP to show a beautiful pitch render (to the MS client) via Lightup, as well as serve as technical layouts, construction details, and work-in-progress sign-off scamps in Layout. The necessary additional detail/model (including glowing inflatable cell-structure) size was killing my renders (and my soon to be updated PC), so I came to the state of breaking the model down and 'sub-render' (eg the exhibition zone) elements. Sketchup & Lightup work brilliantly - it is just the scale of my designs that sometimes get in the way!! I would concur and suggest 'pretty house' and 'real house' models! There are limits with all of this. Good luck with it!

If you export to dxf you can view in AutoDesk FormIt. http://autodeskformit.com/getting-started-with-formit/

Thanks for the recommendation! I don't know what I did but I just textured a track segment perfectly within 10 seconds. There must be magic involved. Edit: I made a video about it: http://www.youtube.com/watch?v=_E0k-t5qEEg

That's the trick! THANK YOU very much!

Brilliant.......does exactly what it says on the tin, just what I wanted

Thanks Thom.

i was able to download su animation software....but i could nt use it....can someone give me guide me on how to use it....

@unknownuser said: http://sketchup.google.com/3dwarehouse/details?mid=c15010c5bf3a6eedc7eab6dd87fa39a9&prevstart=0 OMG! that WC looks flooded

Thanks to both of you! can't believe I've been using su for so long and didn't notice the segment count. anyway, I extended the lines and then used stray lines to select and delete the edges - guess thats the best it gets and thats not too bad thanks again