Remus, sometimes you should read more carefully. (<-Wicked wink) Ken probably knows how to assign shortcuts - what he is aking is how to import them! (Sorry Ken - I have no ida, I'm on PC)

@solo said: I assume this is kinda what you wanted. [image: samplecutoutsas0.jpg] There you gogo solo.

@hazza said: @hazza said: Then right click again -> Rotate - > 90 (or 270) .... and if you have multiple faces that need rotating: click off the face so that the coloured pins disappear but the face is still selected, click the "eye dropper" in the materials dialog box, sample the rotated face, click any other face that needs it's texture rotated. ...and here I have been using Sketchup since 2002 and I never knew! I could have saved so much time in the past. This program rocks (usually)!! Thanks for this.

if I remember well, the width and heigth of your frames must be multiplies of 4: this means that the codec can compress a 800 x 600 PX video, but not a 807 x 603 one. Some codecs require a multiply of 8. I'd use a DVX or Xvid codec: they allow you fast compression and good quality. [/matteo]

@watkins said: Dear Paris, I would draw my square and make it a group. I would then draw my post/spindle at one corner of the square and then make it a component. I would then move and copy the post the required spacing, and then use *N to repeat the move/copy N times. Lastly, I would rotate/copy the array around the centre of the square to complete the four sides. Rotate 90 dgrees first, and then enter *3 to complete the square. Regards, Bob Thx Bob, It didn't occur to me to rotate within a square.

It is too bad that we can't snap to end and mid points with just faces showing. This on its own with display of lines not connected to mesh, could be a mode that would be very Open GL friendly.

You beat me too this, Kenny...and thanks for that and putting the question so well. So, I second the question?

Interesting Thomas, One would think that if it works for Poser, a similar way could be found for sketchup. But what about Vista (and its 64 bit versions)?. Vista has the 3B switch 'on' by default, but in a global way, not per application... I am not having the impression that SU is large adress aware in Vista neither (=I experience the same crashes as I used to have using XP 32 bit when exporting large SU files to a render engine).

Zoom Window was in the toolbar in previous versions but has been moved to the Camera Drop down - but is there any way to add it back to the Toolbar - so much easier than keyboard or drop down? Thanks, Chuck

Hi Alan, Yes, that was the problem. I thought I had already scaled to the correct size and didn't think to check that. Thanks for helping me solve this. Regards Mr S

thanks guys, this has helped explain alot for me.

3DS Max has that feature: http://www.evermotion.org/tutorials/compositing/arch/

@ geh Of course I have used Soap Bubble I retake the lines of Modelhead As Plot-Paris said Bubble Soap must have closed lines So you must trim your boat for have some parts closed Here I have added a vertical line The blue line is closed! When a part is Soap Buble made, make the same for the contiguous part etc... For easy use put each part on a different layer View top is not helping for the concept As you see I had skiped the second horizontal line! [image: bpBp_concept.jpg]

~i have the same problems.

Thanks. It's always helpful to know the underlying reasons. I'll try exporting to a 2D image at high resolution when I need to print. Julian

Hi Chris, Her is a little translation of Matt666 thread : Import the component you want to update : File -> Import In "Window -> Components -> Select -> In Model", right clic on the component which has to be replaced and clic on "Select Instance" [image: file.php?id=14476&t=1] Right clic on the new component you have just import and clic on "Replace Selected" [image: file.php?id=14477&t=1] Ciao, Oli

Hi all, I have been working on getting complete construction takeoffs from models for some time now and i have come to the conclusion that it can be done accurately but the time taken to draw the model up is sometimes greater than the time it would take to do a manual (computerised) take off. so at the moment I am at a point where I need to rethink my approach. I have a few good ides of an easier way but I need to learn a little ruby first. I must say that the cutlist5 ruby is by far the best for carpenters and I hope that Chris's Namesets can come up with something a little more polished. For me and I guess a lot of other sketchupers who are in construction a total package more simple yet more comprehensive than rp reports ($1500 are they kidding?) and more versatile than cutlist5 would be ideal. I am going to have to dig out my geek glasses and build it from scratch. I will keep you all posted. P.S has any one tried cutlist6, I have it loaded but every time i try to open it I get a URL link error. Am i just a gumby or do you all have this problem? If any one could shed some light on its new features, please post them here. Cutlist 6 may have what cutlist 5 is lacking... and then I may be able to put my geek glasses back in my pocket! Or even better sketchup 7 will come out with a varation of all the above and we can all estimate easily.

Thanks Tom, I thought about that as one way. That would require finding the center point of the curve. The method that i used was draw a line perpendicular to each mullion. Then align each bracket to this line. BTW when zooming in how can I avoid the clipping of the view that occurs? Im having a tough time getting in close to view things. I know this has been talk about quite a bit but never knew if there was a solution. I tried changing zoom factor but this did not help.

About the beta 2.0 of 21 september 2008 @unknownuser said: both of these reported SketchUp bugs (missing faces when a polygon's points are too close together less than 0.001, and unit system scaling wrong) are now fixed up for the next beta release. Michael So wait the next

For personal use (its free, but you have to register) I have MojoPac installed on a portable 250GB USB Hard Disk. I use nearly all my applications on the move including Adobe Creative Suite and SketchUp. Plug in to any host PC (providing it has a modern spec), log in, and away you go. You use your own personal environment on the "guest" PC. No files or any sign of your activity is left on the host PC when you log off. It still has a few minor bugs but nothing that has really caused me any serious problems. Visit: http://www.mojopac.com/ Regards Mr S