@geh4evr said: Or there's Hypershot: http://www.bunkspeed.com Very easy to use, and very quick. And fabulously expensive at usable resolutions Anssi

You can made it with Soap Bubble Skin Plugin [image: PaSO_soap.jpg]

You have the DB.Tools who clean all edges of a same coplanar surface!

Hi Louis welcome to SU Community We are located all around the planet. It's nice to share with friends all over the world. MALAISE

Welcome Geocine! Nice looking avatar . I didn't sign any 'NDA' so luckily I can mock the slow dev as much as I want, without spilling any of that top secret Pentagon mumbo jumbo. But seriously: we all are impatient to see what the next SU will be like.

No,it is not stuck.If you see PM's in there, it means that they are sent already but haven't been read by the addressee. Once they read them,they will "move" to the Sent messages folder. Two ways to contact the administrator: send me a PM (I read every PM, don't worry) send me an email (the link is in my signature) To find out who to ask for help, go down to the bottom of the board index and click on the "Administrators" or "Moderators" link. Or even better, in the "Who is online" list, you can always see which moderator (in bold) is online at the moment. You can always send them a PM - they (we) are here to help you.

thanks. you guys been a great help...

I hope you do not mind me adding 'Su2Pov' to your title, as I do not use the app and it may attract the help you need from the developer or knowledgable user.

Seems you can with the Joint Push Pull plug by Fredo666 [image: mLmp_jpp.jpg]

@gaieus said: No, Remus' solution is easier: draw a triangle offset it simply move the inner triangle up (or down) The side faces will be created automatically (by the autofold feature). Ahh ha ha ha... I missed his offset reply because I went to try the the scaling solution.

If it's a component then editing one component changes all of them. If it is a group then you have another issue all together because a copy of a group is not linked and they can be altered seperatly. If it is a component and you want to make it a different colour then right click and select "Make Unique", you will now have another component in your list called "Floor#1", you can then change the name to "Kitchen Floor".

If it is already a component or group first you have to: Explode it, OR Double click the item to edit it THEN you can draw the circle to push/pull it. If you just erase the circle all you do is have a hole in the face of the item. If you want it so that there is a face on the inside of the item then you need to push/pull it. Have a look at the demo model. circle-demo.skp

here's how I did it (fastest method): triple click on the jet plume, this selects all hold shift and click on the SURFACE of the plume, this deselects the fire surface but has all the edges selected right click on an edge in the selection and say "hide" i think this worked because you must have started with a cylinder at some point, similar to my previous post here [image: ApvO_JetPlume2.jpg]

Hi Gigi, hi folks. Sorry for the text being cut off. I made that tutorial on an 19 inches monitor and, if viewed on anything smaller, it may produce that result. Simply zoom out to get the whole picture. You may also pan if required. This tutorial is simply a SKP model using Scenes. Use the Scenes tab on top of the model window one by one and in numerical order in order to follow the development of the modeling. When you have an inference that suits you, remember to press and hold the SHIFT key to lock it. While still maintaining the SHIFT key down you can continue with the drawing operation (line drawing for example). For a parallel line, you use these steps: 1 - Find the starting point with the inference from the center of a circle. 2 - Click on the center to start the line. 3 - Place the cursor over a line that you would like to be parallel to. Wait for the pop-up stating "On edge". 4 - Place the cursor in such a way that you get a line attached to the staring point already defined and in a direction roughly parallel to the line inferenced at step 3. Wait for the magenta inference and the pop-up. 5 - Press and hold the SHIFT key to lock the inference. 6 - Move the cursor along the required direction and for the required length. Use the VCB, if required to specify the exact length. 7 - Click to set the end of the line. 8 - Release the SHIFT key. Just ideas.

it all depends on the codec used. try also uncompressed when exporting.

Hi Aaron, You will need to use the follow me tool (scroll don to the bottom where a cone is made similarly) to model a dome. Also see attached file for ideas (open it and lick on the scene tabs). Ah yes, and welome. I used to suffer with my first domes until I found out how easy it is to make one with a couple of clicks You can also turn on hidden geometry (view menu) to se how your new ome is constructed. You could have, of course, hand stitch your "wireframe" dome from endpoint to endpoint to achieve it and then soften all the lines. Sometime (with lesst regular geometry) that is actually the way we do it. DomeTut.skp

Im guessing the problem is that the laptop doesnt have a graphics card. This means no opengl support and being stuck with hardware acceleration off. Not really a lot you can do about it unless you want to buy a new laptop.

I'm looking for something that can walk me through how to use this plugin.

there shouldnt be any difference between direct x 9 and 10 when your using SU. As for your original problem, have you tried messing about with the opengl settings? (window->preferences->opengl-> fast feedback and hardware acceleration.) Theres a slim chance it might be your problem.

Go to User Control Pannel (on top left of the board index page) then Usergroups and select the french forum.