[Plugin][$] TopoShaper - v2.7a - 01 Apr 24
-
@fredo6 said:
@orei: the spikes are due to singular points with very different altitudes compared with immediate neighbours. TopoShaper CloudPoints generates a surface passing through the points.
My suggestion would be that:
- you generate the group of isocontours from the triangular mesh (an option in TopoShaper Cloud)
- then from the isocontours group, you generate a quad mesh terrain, using the other tool of TopoShaper.
This will smooth the spikes
Sorry Fredo, tried to do what you suggest, but nothing change. I generate the group with triangular mesh (how always i did) and peek and deep are present. After that, used the quad mesh terrain, but peek and deep still present.
Could you, please, verify those things with my skp file previously attached to last post?
Thanks mate. You are the best!!!
-
Orei,
Your cloud points data includes these sharp peaks and deeps. Because TopoShaper Cloud ensures that the terrain surface goes through ALL the points, these peaks will be reflected in the terrain.
If they do not correspond to the reality, then simply discard the points or change their altitude.
Attached is the file with your original points in both Triangular and Quad Mesh mode.
Fredo
-
@orei said:
@fredo6 said:
@orei: the spikes are due to singular points with very different altitudes compared with immediate neighbours. TopoShaper CloudPoints generates a surface passing through the points.
My suggestion would be that:
- you generate the group of isocontours from the triangular mesh (an option in TopoShaper Cloud)
- then from the isocontours group, you generate a quad mesh terrain, using the other tool of TopoShaper.
This will smooth the spikes
Sorry Fredo, tried to do what you suggest, but nothing change. I generate the group with triangular mesh (how always i did) and peek and deep are present. After that, used the quad mesh terrain, but peek and deep still present.
Could you, please, verify those things with my skp file previously attached to last post?
Thanks mate. You are the best!!!
I find that if you to as Fredo suggests: generate terrain from the isocontours, you get a much more regular terrain and you can smooth the few remaining anomalies more easily. If you have bad points in the cloud, there is nothing the plugin can do to change that, but the above procedures helps to "average" them out some.
-
good...cool...cool good ....hehehehe
-
One suggestion.. Can you make option maybe in the next reliese.. "Stick with orriginal contours" for triangulated mesh.. So the plugin would not make triangles between not adjacent contour lines (for example one point of triangle on hight=2m another h=3m and third h=5m). Could be done by inforcing engine to require for points two the same hights and fird different.. simple check.. I'm crab with programming but could be nice add on.. I usually have to stick with orriginal contours...
-
http://www.scriptspot.com/3ds-max/scripts/instant-meshes-bridge
Fredo, could Toposhaper follow the contours as shown on attached gif?
And, generally speaking, is doable to make a bridge to this external free retopologizer?
(https://github.com/wjakob/instant-meshes)
Or make something similar but independent?
-
Well. I know how to constrain the triangulation to the contours. Simply, that's not a trivial development and it requires some time. But it should come.
Fredo
-
Getting some Ruby errors with latest version,
Date: 28-Aug-16 15:37:45
An error occurred in CALCULATING TERRAINS
The operation is fully abortedundefined method `x' for nil:NilClass
mesh.rb: 134 -- ==
TopoShaperAlgo.rb: 1996 -- block (2 levels) in hull_exclude_nodes_outside
TopoShaperAlgo.rb: 1996 -- each
TopoShaperAlgo.rb: 1996 -- block in hull_exclude_nodes_outside
TopoShaperAlgo.rb: 1979 -- each
TopoShaperAlgo.rb: 1979 -- hull_exclude_nodes_outside
TopoShaperAlgo.rb: 1089 -- grid_mark_contours
TopoShaperAlgo.rb: 535 -- top_analysis_contour
TopoShaperAlgo.rb: 418 -- top_processing
TopoShaperTool.rb: 574 -- algo_processing
TopoShaperTool.rb: 666 -- execute_validate
TopoShaperPalette.rb: 130 -- execute_from_palette
TopoShaperPalette.rb: 76 -- notify_from_palette
TopoShaperPalette.rb: 518 -- call
TopoShaperPalette.rb: 518 -- block (2 levels) in palette_validate
body_Lib6Palette.rb: 3058 -- call
body_Lib6Palette.rb: 3058 -- execute_button
body_Lib6Palette.rb: 2865 -- onLButtonUp
Lib6Palette.rb: 93 -- onLButtonUp
TopoShaperTool.rb: 984 -- onLButtonUpThoughts? If it is helpful i have attached the file i am having trouble with.
-
OK upon further inspection the errors above were causd by a conflict between toposhaper and the flux.io plugin for sketchup. Hope this is helpful for someone.
-
After created a terrain, is there a way to show the "grid" on it? I see only the surface but would be nice to see the points of the grid for editing.
-
Are you generating the terrain
- from Isocontours
- or from a point cloud ?
And what is exactly the "grid" you mention. Is it the 'flat' horizontal grid used for projection ?
Fredo
-
Hi everyone.
I am an architect in Turkey.
I model my terrain but I dont put my road in my terrain.
It gives an error. (Unable to triangulate road surface. Try using smaller max road Segment Lenght.)I try lots of times but it gives same error.
Please look at attachment. Pls help me.
-
@smhbrv said:
Hi everyone.
I am an architect in Turkey.
I model my terrain but I dont put my road in my terrain.
It gives an error. (Unable to triangulate road surface. Try using smaller max road Segment Lenght.)I try lots of times but it gives same error.
Please look at attachment. Pls help me.
Who can help me ?
-
Why not use the SandBox / Project ?
-
Hello Fredo: I just started using Toposhaper. It works fine, but the dialog box text is so small I can hardly see the text. Is there a way to adjust the text size? I am using an iMac with Retina display.
Thank you for all your contributions...
Jim S -
NEW RELEASE: TopoShaper v1.3a - 17 Jan 17
This is a minor release with SU2017 certification
See main post of this thread for Download.
Fredo
-
I am having trouble installing the toposhaper extension in SUMaker2017 and get the following after restarting SU. Any suggestions would be appreciated
-
@dvdstwrt said:
I am having trouble installing the toposhaper extension in SUMaker2017 and get the following after restarting SU. Any suggestions would be appreciated
You seem to have missed off the error message ?
Have you also installed the needed LibFredo?
Also check that both Extensions are activated and restart SketchUp to ensure any changes/additions are fully integrated... -
Fredo, your plugins are mindblowing!
-
Every time I start sketchup I am receiving the following pop up.
All my fredo plugins are updated. I checked it with the feature of fredo tools itself.
What should I do to resolve this issue?
Advertisement