[req] a good stairmaking plugin

rock1

Something like this Rock?

hey how did you make them!! I wanna know

bac9-flcl

@sdmitch said:

Something like this Rock?

hey how did you make them!! I wanna know

http://sketchup.google.com/intl/en/training/videos/new_to_gsu.html
http://sketchup.google.com/intl/en/training/videos/familiar_with_gsu.html

Have you studied these? "Copy and Arrays" tutorial in particular.
There is nothing complicated in there. ))

Edson

the sketchup show #38 part 1 and part 2.

sdmitch

rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.

rock1

@sdmitch said:

rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.

well which plugin r u using?

sdmitch

@rock1 said:

@sdmitch said:

rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.

well which plugin r u using?

rock1

@sdmitch said:

@rock1 said:

@sdmitch said:

rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.

well which plugin r u using?

don't mind but can you upload here?

Dave R

I expect he would have uploaded it here already if he'd been interested in sharing with you.

sdmitch

Well Dave he never asked for it, only about it, so I fealt no compulsion the give it.

Rock, the plugin in question is attached. You can access it through the Plugins menu. There are 3 options, Normal, Spiral, and U-Shape.

Normal is just a straight run with a railing on one side. The steps are a group and the rail is a group.

Spiral is a circular or elliptical stair depending on the Max,Min width input. It is a single group.

U-Shape now accepts "turn steps" which replace the landing if defined. This is a single group also.

Stair Maker

rock1

@sdmitch said:

Well Dave he never asked for it, only about it, so I fealt no compulsion the give it.

Rock, the plugin in question is attached. You can access it through the Plugins menu. There are 3 options, Normal, Spiral, and U-Shape.

Normal is just a straight run with a railing on one side. The steps are a group and the rail is a group.

Spiral is a circular or elliptical stair depending on the Max,Min width input. It is a single group.

U-Shape now accepts "turn steps" which replace the landing if defined. This is a single group also.

that's so kind of you , thanks a lot people like sdmitch are men of honour. Look fellas, these are men of honour, these are men of honour!!

utiler

@sdmitch said:

Well Dave he never asked for it, only about it, so I fealt no compulsion the give it.

Rock, the plugin in question is attached. You can access it through the Plugins menu. There are 3 options, Normal, Spiral, and U-Shape.

Normal is just a straight run with a railing on one side. The steps are a group and the rail is a group.

Spiral is a circular or elliptical stair depending on the Max,Min width input. It is a single group.

U-Shape now accepts "turn steps" which replace the landing if defined. This is a single group also.

G'day Sam, nice little plugin!

I have some ideas for you to add if you could to extend it a little more.... see attached PDF.

stairMaker.pdf

charly2008

Thank you very much Sam,

a very useful and time saving plugin.

Charly

sdmitch

Andrew, I will take a look at your suggestion and see what I can do. Some are trivial like asking for and using a given gap between the runs and the height and offset for the handrail. The "in-situ" option not so trivial but I'll see what I can do.

utiler

Thanks Sam, appreciate it!
Also for your u-shape stair maybe add a tread thickness and make treads components... Just helps with edits.
Well done, mate! simple and very effective tool!

sdmitch

Andrew, I think I have incorporated all the changes you suggested except make the treads components. Maybe in version 3.

Stair Maker