[Plugin] FredoTools::CurviShear 1.5a - 25 Aug 11 (ramps)

CodyV1 · 7 Jul 2010, 04:02

This is great! How ironic I find this on the site when X Games rolls in. I think this would be great if it somehow incorperated banking. I'll be saving time by the hours with this on road courses

halroach · 7 Jul 2010, 08:01

@unknownuser said:

Hi Fredo,

I know the plugin contains the word curve in it ... but would there be a way to get it to work on any geometry that isn't necessarily a curve?

I may have confused the plugin's functionality.
I guess I was thinking of something a bit different for ramp creations. You would push a curved surface onto a straight plane. Like Joint Push Pull but to a horizontal surface. You would use it when you have the ramp already created but don't have the base for it... how does that sound?

Macker · 7 Jul 2010, 10:41

Would it be able to do a ramp with say a "T junction" half way up? I'm just thinking about how to go about doing roads on uneven sites, which often have various junctions and so on.

mitcorb · 10 Jul 2010, 01:54

@Macker:
I just tried a simple T Junction with Bezier curves, but I stubbed the ends with straight segments and ran the ruby. The script could not decide which end to set as the low elevation and which to set as the high. So it basically did both elevations for all four stubs, leaving a wire frame mesh as a group.
However, after throwing that away, I did a simple ramp and added Bezier plan profiles to the curvishear ramp and pushpulled the stubs up to the nearest point above and then adjusted them to coincide with the main slope. Not necessarily the best way, but one possible solution while we wait for any enhancements to this handy little tool.
Best Regards,
mitcorb

kobus · 20 Sept 2010, 07:57

Respect, Fredo.
Every once in a while a gem like this is there exactly when I need it.
I'm going to include "difficult ramp for parking" here so people get this topic at the top of the list when searching. Many thanks !

grim · 22 Sept 2010, 05:07

fredo

i realise this was just a quickie ruby but it is a good one that i use

however i am haveing trouble in SU8 is there a problem and does it need updating

regards
grim

thomthom · 22 Sept 2010, 06:21

@grim said:

however i am haveing trouble in SU8 is there a problem and does it need updating

It helps to describe what the trouble is.
(Operations fails, error messages, messages in the Ruby Console?)

Krisidious · 22 Sept 2010, 06:59

punctuation helps too... are those questions or statements?

pilou · 22 Sept 2010, 07:27

If some modifications are made for the V8, what are the results for the previous versions?

thomthom · 22 Sept 2010, 07:39

@unknownuser said:

If some modifications are made for the V8, what are the results for the previous versions?

Should be none - Ruby 1.8.6 has stricter parsing which has been the biggest cause of the incompatibility.

fredo6 · 22 Sept 2010, 12:18

@grim said:

fredo

i realise this was just a quickie ruby but it is a good one that i use

however i am haveing trouble in SU8 is there a problem and does it need updating

regards
grim

CurviShear should work in SU8.

Do you experience problems?

Fredo

monkeybss · 22 Sept 2010, 16:47

Thanks, I very much needed this, life is going to be easier now...

grim · 22 Sept 2010, 22:54

fredo
yes i seem to have a problem see image attached , with a single arc it works fine, with a double arc and weld plugin used i get a mess

regerds grim

fredo6 · 23 Sept 2010, 06:47

@grim said:

fredo
yes i seem to have a problem see image attached , with a single arc it works fine, with a double arc and weld plugin used i get a mess

regerds grim

Could you post the skp file so that I have a look

Thanks

Fredo

rv1974 · 26 Oct 2010, 10:50

Hi fredo!
Please take a look at this:
http://www.scriptspot.com/3ds-max/scripts/ant-stitcher-fast-and-easy-way-to-connect-two-meshes-in-3ds-max
If only you could add a similar feature it'd become a mega hit!

arjunmax09 · 27 Dec 2010, 15:50

I'm trying to make a ramp using curvishear and curviloft but not getting the desired result. I've attached a video of what exactly happens during the process

trying to make Ramp.rar

jeff hammond · 27 Dec 2010, 16:33

arjun,
try using the 3rd icon in curviloft.. skinning of shapes

arjunmax09 · 27 Dec 2010, 16:56

@unknownuser said:

arjun,
try using the 3rd icon in curviloft.. skinning of shapes

i tried using that but nothing happens..can you post a video or some screenshots?? I've uploaded the model btw..

rr5 low.skp

Daniel S · 27 Dec 2010, 17:53

@arjunmax09 said:

@unknownuser said:

arjun,
try using the 3rd icon in curviloft.. skinning of shapes

i tried using that but nothing happens..can you post a video or some screenshots?? I've uploaded the model btw..

Works for me...

Like Jeff said.. try using the 3rd icon... not the first one:

Here I attach the result:
rr5 low.skp

Daniel S

arjunmax09 · 28 Dec 2010, 04:33

@daniel s said:

Works for me...

Like Jeff said.. try using the 3rd icon... not the first one:
[attachment=1:1596wm15]skin.jpg[/attachment:1596wm15]

Daniel S

Daniel...i used the same button for making the ramp...i select all the edges but nothing happens..Please upload screenshots or a video of how you actually make the ramp...I'm using SU 8 Pro..??