[Plugin][$] RoundCorner - v3.4a - 31 Mar 24

[TIG]

Unlikely to result in faces <1mm ?

[Gaieus]

I have also had a couple of crashes but definitely not 70%. In fact, other plugins can also cause crashes (especially when I do not "notice" how big task I want to feed the plugin with) so at least I am used to saving before I run anything (except of course at the most crucial moments )

[ken28875]

@tig said:

Unlikely to result in faces <1mm ?

What do you mean, TIG?

Thanks,

_KN

[brookefox]

My first use of this wonderful tool leads me to make a newb suggestion and ask a newb question.

S: It would be nice to have persistent settings for each of the three round types independently as, for instance, I generally want beveled edges unsmoothed but the others likely not.

Q: With a surface whose edges have been beveled and unsmoothed and which appears flat and untextured, what causes the slightly modeled appearance (slight shading effects not visible elsewhere)?

[TIG]

If a 'followme' type tool makes faces with dims <~1mm it will cause failures - a limitation of OpenGL ?
I thought you might be making the equivalent of a 'followme' around a tight curve that made these small facets and crashed - but maybe not ?
Can you successfully make the equivalent rounded/chamfer using the FollowMe tool 'raw' ?

[ken28875]

Hi TIG,

I don't have any problems with the Follow-me tool.

Sketchup crashes only when I use RoundCorner.

Thanks,

_KN

[fredo6]

@ken28875 said:

Hi TIG,

I don't have any problems with the Follow-me tool.

Sketchup crashes only when I use RoundCorner.

Thanks,

_KN

Ken,

Could you post or send me the model, so that I can have a look at whatcrashes.
I assume that you also upgraded to the latest version. There was a previous release that had reported crashes.

Fredo

[fredo6]

@brookefox said:

S: It would be nice to have persistent settings for each of the three round types independently as, for instance, I generally want beveled edges unsmoothed but the others likely not.

Normally the persistence is done for each individual tool, including the custom saving by the icons A, B, C, D

@brookefox said:

Q: With a surface whose edges have been beveled and unsmoothed and which appears flat and untextured, what causes the slightly modeled appearance (slight shading effects not visible elsewhere)?

I am not clear of what is the bad visual effect. Coul you post a picture or the model.

Fredo

[ken28875]

@unknownuser said:

Ken,

Could you post or send me the model, so that I can have a look at whatcrashes.
I assume that you also upgraded to the latest version. There was a previous release that had reported crashes.

Fredo

Hi Fredo,

I just sent you a private message. Unfortunately I could not attach the file. It's bigger than the allowed size of 4mb.

Thanks,

_KN

[brookefox]

@unknownuser said:

@brookefox said:

S: It would be nice to have persistent settings for each of the three round types independently as, for instance, I generally want beveled edges unsmoothed but the others likely not.

Normally the persistence is done for each individual tool, including the custom saving by the icons A, B, C, D
Fredo

Sorry, I missed that and will investigate further. Thank you.

@unknownuser said:

@brookefox said:

Q: With a surface whose edges have been beveled and unsmoothed and which appears flat and untextured, what causes the slightly modeled appearance (slight shading effects not visible elsewhere)?

I am not clear of what is the bad visual effect. Coul you post a picture or the model.

Fredo

Its only very slightly 'bad'. My understanding is worse, though, and that is what I was wanting to improve.

---

[thomthom]

Are the edges Smooth by any chance?

[brookefox]

Well, obviously, I mean, well, er....

I thought I had checked that but obviously my methodology was seriously flawed.

Thanks, t.

[Cris999]

Hello

Is there another place to download this plugin?
I tried with this one, but it gave me the message "The Compressed (zipped) Folder is invalid or corrupted".

Thank You, Cris999

[TIG]

The 2.1c zip is fine I just re-downloaded it to test... Try again.

[Cris999]

I tried on other PC too. Same problem. Can somebody send me the unzipped files on PM?
Thank You

[fredo6]

@cris999 said:

I tried on other PC too. Same problem. Can somebody send me the unzipped files on PM?
Thank You

Which unzip program do you use?

Fredo

[Cris999]

First: I tried to selfextract the file.
Second: it was 7-Zip
Third: WinAce
Forth: I used a online unzipper service
Fifth: I sent the file to somebody, asking him to unzip
Sixth: I downloaded from another PC and tried unsuccessfully to unzip
Only WinAce showed my the 2 "IMAGES" folders and english pdf file (the french one is corrupt) and no other files in "ROUNDCORNER_Dir_21" folder

Thank You, Cris999

[fredo6]

@cris999 said:

First: I tried to selfextract the file.
Second: it was 7-Zip
Third: WinAce
Forth: I used a online unzipper service
Fifth: I sent the file to somebody, asking him to unzip
Sixth: I downloaded from another PC and tried unsuccessfully to unzip
Only WinAce showed my the 2 "IMAGES" folders and english pdf file (the french one is corrupt) and no other files in "ROUNDCORNER_Dir_21" folder

Thank You, Cris999

Maybe you should try to download WinZip (this is what I use to zip the files).
In any case, be attentive to the hierarchy of folders that should be recreated. I would suggest you unzip in a neutral place, then check and then copy the folder and small file in the SU Plugin directory.

Fredo

[xrok1]

i dblclick to open with 7zip then drag and drop files/folders to SU plugins in another open explorer window. never fails.

[blair]

Some time ago I used Fred06.s "[Plugin] RoundCorner" to round/bevel an edge then saved the file. Now I have decided the round/bevel edge is to large. Is there a way to undo the round/bevel and start over from a square edge and do it all over again without a re-draw?