What's this?
-
Now there's an idea
-
The Sqhair
Economical on material too.
Simply table-sawn and router rounded-corners etc as needed etc.
The table can use a simple foot-operated bottle-jack mechanism to lift it up and on release lower down.
The storage under the seats is set back a little to avoid heel-clashes.
The seat-back half 'L' slides up/down on dado friction glides [à la draw-slides] with a catch to it lock 'up' ?
When the seats are removed from the assembly they are set around the table at 45 degrees on the sides of the square. The seats are on castors.
-
Nice, but those seat-backs don't look very comfortable
-
Now we are getting places.
TIG, would that table have a bit of wobble potential? Also I think Steve might be right about the backs not being too comfy.
Have you a pic of a 'foot-operated bottle-jack mechanism'? I'm curious about that.
I'm not so sure about the seats being on casters but they could be lockable. I think slides might work better.
-
An octagonal shape applied to TIG's design would sort out the seat backs.
-
-
One possible solution to the seat-back
Sorta looks like a toilet with the seat folded down
-
Maybe a couple of padded armrests for comfort (they could flip up for extra storage)
-
Nice render Pete. But that a full size table. We are trying to figure out a dual coffee / dining table.
Steve, yep! It does look like a commode ..... maybe an idea?
-
When the meal is just too good to interrupt.....
-
-
...... now a sound proof private curtain
-
Some cultures consider it a compliment to the cook when you belch at the table. This just takes the compliment to a whole new level.
-
.....may as well go the full hog and build in an air extractor
-
-
Here's v3 - it has a more logical base made from swastika dado lapped 'base-feet' and a simpler back made form the same thickness foam as the seat...
-
Good idea to make the seat-back lower with the rest of the back. I enjoy seeing how a project develops.
Some questions -
Why not make the seat-back flush with the top of the L-shaped assembly? It's very low anyhow, this would give more support.
Are you going to round the edges of the wood?
Will there be some sort of handle/cutout to grasp to raise/lower the seat-back?
I'll go away now
-
@hellnbak said:
Good idea to make the seat-back lower with the rest of the back. I enjoy seeing how a project develops.
Some questions -
Why not make the seat-back flush with the top of the L-shaped assembly? It's very low anyhow, this would give more support.
Are you going to round the edges of the wood?
Will there be some sort of handle/cutout to grasp to raise/lower the seat-back?
I'll go away now
The top of the 'pad' is lower because it must fit under the table top in the lowered-position.
This small upstand gives something to hold when sliding the L-shaped-back upwards.
It could incorporate a routered 'internal' horizontal finger 'groove' for a grip - leaving the outside faces all similar and flush/flat.
The main external corners of the panels are shown rounded by 10mm, the other edges of the panels could be given a 'pencil-round' [3mm?]
We have yet to devise 'sliders/locking-catches' for the L-back, the chairs' castors/slides/glides, and the 'bottle-jack' to lift/lower the table-top from 'coffee' to 'dining' ??? -
@hellnbak said:
Good idea to make the seat-back lower with the rest of the back. I enjoy seeing how a project develops.
Some questions -
Why not make the seat-back flush with the top of the L-shaped assembly? It's very low anyhow, this would give more support.
Are you going to round the edges of the wood?
Will there be some sort of handle/cutout to grasp to raise/lower the seat-back?
I'll go away now
The top of the 'pad' is lower because it must fit under the table top in the lowered-position.
This small upstand gives something to hold when sliding the L-shaped back up.
It could incorporate a routered 'internal' horizontal finger 'groove' for a grip - leaving the outside faces all similar and flush/flat.
The main external corners of the panels are shown rounded by 10mm, the other edges of the panels could be given a 'pencil-round' [3mm?]
We have yet to devise 'sliders/locking-catches' for the L-back, the chairs' castors/slides/glides, and the 'bottle-jack' to lift/lower the table-top from 'coffee' to 'dining' ??? -
Beautiful thinking outside the box!
Advertisement