[Plugin][$] RoundCorner - v3.4a - 31 Mar 24

snapster42

That's probably the explanation. A face is created between the big and the small cube.

Actually, RoundCorner does not create the face, it is rather Sketchup that does it automatically (i.e. find_face).

Fredo

cool, thanks for the tip. I'm fairly new to sketchup; any advice on how I delete this internal face? Do I have to hide some visible faces and then delete the internal one or something?
Thanks!

cotty

@filonik said:

Я никак не могу найти где скачать сам плагин.
Не вижу слова СКАЧАТЬ.

Посмотрите в первом посте.

(You should try to use english here in the forum.)

Box

@filonik said:

Я никак не могу найти где скачать сам плагин.
Не вижу слова СКАЧАТЬ.

жми меня

tomot

I don't know if problem has been resolved. I looked at the .rb files but can't a revision date.

see attached pic.

fredo6

Tomot,

What do you mean by inconsistent highlight?

How should the corner and roundings be to be OK?

Fredo

Pherim

SU2015 64bit sometimes crashes immediately after I use roundcorner... I have the newest version and I installed it with the Plugin store tool, it also works perfectly in SU2013.

edit: it only seems to happen on geometry that already existed in a model I took over from SU2013, but if I create new objects it works on them... strange.

edit2: no, I was wrong, it always crashes on geometry inside Components! It may be that another plugin is responsible for this that I haven't installed in 2013, need further investigating.

edit3: Alright, it's not SU2015! Apparently Components Manager causes the crashes. I didn't have that installed before, so it was one of the most probable suspects for this.

tomot

@fredo6 said:

Tomot,
What do you mean by inconsistent highlight?
How should the corner and roundings be to be OK?
Fredo

I'm not being critical of the plugin, perhaps its a rendering issue.
I'm trying to find out why the HDR light striking the rounded corners is not uniform along the rounded edge of each Tile as I try to show in the pic by the red line

For example if I had a number of tiles with rounded edges sitting in sunlight, Each rounded edge along each tile would reflect the sun uniformly. not only for 1 tile but also all other tiles.

nickcconnor

Thanks Fredo6, your round corner plugin has been a wonderful tool - really solid and reliable - thank you so much.

I was just wondering if there were any issues running this in sketchup 15, as it doesn't seem to install for me?

Thanks again,
Nick

cotty

It's 2015 compatible.

TIG

It's fine in v2015.
Do you also have the latest LibFredo... ?

kittiset

thank you

buinhuthuong

thankyou

Hieru

Has anyone else found the plugin to be a but buggy with 2015?

I'm using the latest version (along with the latest LibFredo) and I regularly find that I can't select edges on basic shapes with one or all of the RoundCorner tools.

After restarting my PC everything usually goes back to normal, but the plugin will suddenly stop functioning at some point during a modelling session.

Rich O Brien

It's good one my end but I'm running very little enabled addons.

Dave R

I use Round Corner quite frequently and I haven't seen any problems with it at all on SU2015. it has behaved very well.

Hieru

@rich o brien said:

...I'm running very little enabled addons.

Me either...I'm still in the process of adding them as needed. Maybe there is a conflict that didn't crop up in 2014, so I'll try disabling everything else and see what happens.

Hieru

OK, so I've tried disabling all other plugins, but no luck.

I've also completely removed Round Corner and LibFredo from the plugin folder and reinstalled them. Again no luck....when I try anything other than Sharp Corners I get the warning "Invalid (Property filter)".

I haven't tried installing manually (without the Sketchucation tool).

Rich O Brien

Can you share or show an example mesh?

fredo6

@hieru said:

OK, so I've tried disabling all other plugins, but no luck.

I've also completely removed Round Corner and LibFredo from the plugin folder and reinstalled them. Again no luck....when I try anything other than Sharp Corners I get the warning "Invalid (Property filter)".

I haven't tried installing manually (without the Sketchucation tool).

The message "invalid (property filter)" comes when you select an edge with NO face.

So you may want to inspect your model and see if there is no hidden edge defect.

Fredo

Hieru

Thanks guys, but I've solved the problem now.

For some reason the edge properties were set by default to 'soft' only. Not sure if that's a bug or a d'oh! moment on my behalf.