[Plugin] Double line
-
Damned I have x for X-Ray
So my previous trick will work fine again@unknownuser said:
Just write any number like 1
then backspace for erase it
then write x
then EnterIt's like Glen Gould but works
-
@didier bur said:
Patch published today. Shortcut for "close" changed to "x" instead of "c".
Didier
Using "X" is a good choice: x is usually reserved for copying - e.g. x3 to make copies within other commands and isn't a shortcut... If like Pilou you want to use 'X' as a shortcut for something like X-ray you need to remember to use 3x for copies rather than x3, as the latter will invoke X-ray rather than make copies ! Persoanlly I use Alt+X for X-ray mode...
-
@unknownuser said:
use 'X' as a shortcut for something like X-ray you need to remember to use 3x for copies rather than x3
cool little trick
-
Great work, Didier! Thanks so much for sharing!
a couple little things:
when I choose "show axis"... it does not show... whether or not I have it pop the wall up.After drawing a wall, I exit the tool, then I want to draw a double line vertically on a face, so I choose to use the tool again... set width to 12", no face, no close. I draw a vertical line from top edge to bottom edge of the wall face. I hit enter for it to draw the double line. I get this.
-
Thank you very much Didier.
-
Thanks D! I'll have to try it out sometime.
-
Hi,
@unknownuser said:
when I choose "show axis"... it does not show...
Axis is drawn with guide lines (construction lines). Do you have them visible ?
Remember axis will only be visible if justification is "Center".@unknownuser said:
draw a vertical line from top edge to bottom edge of the wall face. I hit enter for it to draw the double line. I get this.
Oh yes, I noticed that here too. The part of line up the wall is always exactly half the width of the wall
As a matter of fact, this is normal: for the script to work in 3D, I had to compute the geometric plane on which the first two segments are drawn. Thus if you click only one segment, two points aren't enough to define the plane of the base. In this case the script considers that the plane is the red-green plane. And your points have the same projection on the red-green plane. So an error occurs. Hope I'm clear, hem,hem...
But I'll try to fix that if I can. -
Hi!
c=circle
x=explode.
Generally the letters are bad idea.
Could it be just cntl click for for close? -
i second that
-
Hi,
Everybody will agree now, I hope. I finally got the double-click detection to work, so a double-clic will close a shape.
Another small enhancement: when you draw only one segment on an existing face, it takes the face as the base geometric plane (to solve Fletch's issue).
Download it at the top of topic.
Regards, -
Users presure
-
Thank you Master Didier!
-
Well, that last fix broke it for me. I like doing one wall at a time, and it now lays them down flat instead of upright. I'm adding walls to an existing framework, so there are planes adjacent to where I'm adding the wall. PS: if I could undo one wall at a time, that would be great - if I make a mistake and undo, I lose all the work I've done with the tool so far. Thanks, CB.
-
Hi,
@unknownuser said:
if I could undo one wall at a time, that would be great
Done. Download it again...
-
Didier,
Thanks for the plugin, it's great! Any plans to incorporate a double line function for an arc type tool as well?
-
Why not...
-
Thanks Didier
-
Didier many thanks for your efforts!
Double click for close is neat idea though I couldn't manage to get good result- it's a bit messy. -
it's a bit messy
? Very clear!
A little trick if you find this difficult
Draw your lines without the plug, group it, then redraw with the plug over them!
Erase the group -
Now I understood: it closes wall in a newpoint not at the first one. I'm spoiled with CAD background )
@Pilou: With pre-drowed lines extrude lines.rb is better choise imho
Advertisement