[Plugin] Double line

lapx

Thanks D! I'll have to try it out sometime.

Didier Bur

Hi,

when I choose "show axis"... it does not show...

Axis is drawn with guide lines (construction lines). Do you have them visible ?
Remember axis will only be visible if justification is "Center".

@unknownuser said:

draw a vertical line from top edge to bottom edge of the wall face. I hit enter for it to draw the double line. I get this.

Oh yes, I noticed that here too. The part of line up the wall is always exactly half the width of the wall
As a matter of fact, this is normal: for the script to work in 3D, I had to compute the geometric plane on which the first two segments are drawn. Thus if you click only one segment, two points aren't enough to define the plane of the base. In this case the script considers that the plane is the red-green plane. And your points have the same projection on the red-green plane. So an error occurs. Hope I'm clear, hem,hem...
But I'll try to fix that if I can.

rv1974

Hi!
c=circle
x=explode.
Generally the letters are bad idea.
Could it be just cntl click for for close?

CadFather

i second that

Didier Bur

Hi,
Everybody will agree now, I hope. I finally got the double-click detection to work, so a double-clic will close a shape.
Another small enhancement: when you draw only one segment on an existing face, it takes the face as the base geometric plane (to solve Fletch's issue).
Download it at the top of topic.
Regards,

pilou

Users presure

CadFather

Thank you Master Didier!

daiku

Well, that last fix broke it for me. I like doing one wall at a time, and it now lays them down flat instead of upright. I'm adding walls to an existing framework, so there are planes adjacent to where I'm adding the wall. PS: if I could undo one wall at a time, that would be great - if I make a mistake and undo, I lose all the work I've done with the tool so far. Thanks, CB.

Didier Bur

Hi,

@unknownuser said:

if I could undo one wall at a time, that would be great

Done. Download it again...

EarthMover

Didier,

Thanks for the plugin, it's great! Any plans to incorporate a double line function for an arc type tool as well?

Didier Bur

Why not...

Mike Lucey

Thanks Didier

rv1974

Didier many thanks for your efforts!
Double click for close is neat idea though I couldn't manage to get good result- it's a bit messy.

pilou

it's a bit messy
? Very clear!
A little trick if you find this difficult
Draw your lines without the plug, group it, then redraw with the plug over them!
Erase the group

rv1974

Now I understood: it closes wall in a newpoint not at the first one. I'm spoiled with CAD background )
@Pilou: With pre-drowed lines extrude lines.rb is better choise imho

pilou

@unknownuser said:

With pre-drowed lines extrude lines.rb is better choise imho

You have not the drawing of the dashed axis line
And you have a thickness with extrude simple lines And a wall

@unknownuser said:

it closes wall in a new point not at the first one

Yes Didier is some original !
It's some pertubating but after some try we are in the move!

rv1974

@unknownuser said:

@unknownuser said:

With pre-drowed lines extrude lines.rb is better choise imho

You have not the drawing of the dashed axis line
And you have a thickness with extrude simple lines And a wall

Pardon, I meant extrude along path .rb (of TIG i beleive).
I'm afraid the wink about dashed line I didn't understand. What do you mean?

pilou

@unknownuser said:

I'm afraid the wink about dashed line

Just this

gogo2suf

Thank You vary much D. Bur ,
Thank you!!!!!!!!!!!!
GOGO

agrazdi

Is it possible to add a png icon into the tool bars for the double line function ?

Thanks

agrazdi