[Plugin][$] RoundCorner - v3.4a - 31 Mar 24
-
It's good one my end but I'm running very little enabled addons.
-
I use Round Corner quite frequently and I haven't seen any problems with it at all on SU2015. it has behaved very well.
-
@rich o brien said:
...I'm running very little enabled addons.
Me either...I'm still in the process of adding them as needed. Maybe there is a conflict that didn't crop up in 2014, so I'll try disabling everything else and see what happens.
-
OK, so I've tried disabling all other plugins, but no luck.
I've also completely removed Round Corner and LibFredo from the plugin folder and reinstalled them. Again no luck....when I try anything other than Sharp Corners I get the warning "Invalid (Property filter)".
I haven't tried installing manually (without the Sketchucation tool).
-
Can you share or show an example mesh?
-
@hieru said:
OK, so I've tried disabling all other plugins, but no luck.
I've also completely removed Round Corner and LibFredo from the plugin folder and reinstalled them. Again no luck....when I try anything other than Sharp Corners I get the warning "Invalid (Property filter)".
I haven't tried installing manually (without the Sketchucation tool).
The message "invalid (property filter)" comes when you select an edge with NO face.
So you may want to inspect your model and see if there is no hidden edge defect.
Fredo
-
Thanks guys, but I've solved the problem now.
For some reason the edge properties were set by default to 'soft' only. Not sure if that's a bug or a d'oh! moment on my behalf.
-
Hi there a question. Does Round Corner work on Sketchup 2015 on Mac? If so, how can I install it? thanks in advance.
-
Hi there.
I have been looking through the topic but can't find any satisfying answer to my problem... I am working on Sketchup 2015 for mac and the RoundCorner plugin keeps crushing it pretty much every single time i try to use it... I have checked all my plugins and they're up to date, so is the v-ray version... Also don't have any error messages when I run the program. But all the plugin needs to crush is simply trying to select or unselect ANY line and bam - there's the bug splat... Any ideas what may be causing that? I'm running out of patience
-
Try disabling the V-ray plugin and see if you still get the crash.
-
Red Foxy, do you have v-ray for SU 2015 for Mac? could you please upload the file? I really don't find any v-ray for SU 2015 for Mac.
-
@dave r said:
Try disabling the V-ray plugin and see if you still get the crash.
Thanks for the quick reply... well, i did that, checked some edges, got all excited, added one more and well.. yeah. bug splat...
So still no solution... Will probably try unchecking and trying all the plugins one by one, maybe i'll find something responsible for that 
Thanks anyway for the suggestion...@diago said:
Red Foxy, do you have v-ray for SU 2015 for Mac? could you please upload the file? I really don't find any v-ray for SU 2015 for Mac.
Yeah, got it from the chaosgroup website
http://www.chaosgroup.com/en/2/vrayforsketchup.html -
Maybe you could post the SKP file that you're trying to run Round Corner on?
-
the whole file is quite big, unless you mean a separate component then sure, but it crashes on things as simple as a cube.. I managed to get 2 surfaces rounded however it took me like 6 attempts or something
this thing really teaches you patience.
-
What edges are you trying to round over? And what values are you using for Offset and the Number of sides?
Patience is good.
-
@dave r said:
What edges are you trying to round over? And what values are you using for Offset and the Number of sides?
Patience is good.
Just the sides of the main box and the parameters were 2mm and 2 sides.
-
OK. I just tried it on my computer and it worked fine. I only selected the front and back vertical edges and the bottom edge. How were you making the selection? Is it possible you were selecting the top edge where the round over has already been done?
-
@dave r said:
OK. I just tried it on my computer and it worked fine. I only selected the front and back vertical edges and the bottom edge. How were you making the selection? Is it possible you were selecting the top edge where the round over has already been done?
I don't think so, i just select the four vertical edges and try to run the roundcorner... As I said before, sometimes it works but it crashes on rather stupid moments such as unselecting a selected edge or something else as simple as that...
Sometimes i feel like with sketchup patience is everything
-
I quickly redrew your cabinet and then rounded over the edges on the top and sides in one go.
I double clicked with Select while holding the Ctrl key (Option on Mac) on all three sides in turn to select their edges and then ran the tool once.
-
@dave r said:
I quickly redrew your cabinet and then rounded over the edges on the top and sides in one go.
I double clicked with Select while holding the Ctrl key (Option on Mac) on all three sides in turn to select their edges and then ran the tool once.
[attachment=1:358glolk]<!-- ia1 -->Screenshot - 12_19_2014 , 4_51_30 PM.png<!-- ia1 -->[/attachment:358glolk][attachment=0:358glolk]<!-- ia0 -->Screenshot - 12_19_2014 , 4_53_49 PM.png<!-- ia0 -->[/attachment:358glolk]
Hmmm... however tempting redrawing around 60 different pieces of office furniture is
I have been encountering this problem with other objects before while working on a completely different project, so from that I take it's rather the issue of program/plugins incompatibility rather than the objects themselves... Thank you very much for trying to help, I suppose this problem is gonna stay unsolved for now, will definitely have to run all the plugins separately to see which one may be causing the errors..
Advertisement