[Plugin][$] Curviloft 2.0a - 31 Mar 24 (Loft & Skinning)
-
I wasn't sure how much nautical knowledge he had so I tried to keep it very simple.
And that IS a good illustration, BTW. -
And here's the same idea again but in SU ready to have the lines traced.
(Plans scanned and imported as images).And below is the (un)finished result. Not sure I will ever finish it.
-
guys, how could i make a surface from those contours? just a narrow face beetween the lines
thnks
-
There could be a number of things preventing the completion of the face within the lines. If you post your .skp file, others can review and advise.
It could be a scale issue.
It could be a non coplanar issue.
It could be a non closed figure.
It could be something else. -
CL will fail on any one of the following most common conditions... (as well as a few others)
- 2 lines not joined at "endpoints" although they look like they do. Endpoints joined when "Constrained by" will not loft.
- a tiny fragment at an endpoint is taken as part of the perimeter CL finds, or you define by selection.
When CL defines its perimeter, use the colours as a guide to where problems may lurk. Fredo has stated that the colours are not meaningful by design, but I have noticed that if the perimeter segment is a complete yellow it has no problems, but that is NOT a given. It can be almost any other colour, and it could still have a problem, usually at the very ends. However I have found that red indicates a problem that could be at either endpoint, or anywhere on the curve.
If a perimeter is made up from several colours, then there may be a problem at the endpoints where the colour changes.
The common fix is to zoom in on the endpoint CL has indicated to perhaps be a problem, and fix it.
Another way is to widely left-to-right select one line segment that includes the 2 endpoints and delete it. That will get rid of any gaps or fragments. Then redraw endpoint to endpoint. Make sure you do not join the lines on an endpoint that is "constrained by" or that is on a point outside the current context.
On a large complex loft you may want to put temporary lines in to breakup the large curve into several smaller ones, and CL each of them. The one that will not loft contains the problem. All this does is narrow down where to look. Delete all the temp lofts when done.
On a long complex curve as you posted, I would split it in a binary fashion. CL one 1/2. If it lofts, split the other half in 2 and repeat. If it fails, split that in 1/2 and repeat. Do this until you get down to a manageable few lines to look at in detail. This does not preclude multiple problems, but it does find clean sections as well as the problem ones.
And finally, when CL does not loft a seemingly clean perimeter that is attached to other geometry in the model, do this;
Select all of the perimeter lines manually and move/copy them to some free space along an axis line. You could also make the perimeter a group and edit the group.
Inspect and fix the perimeter for gaps and fragments.
CL should then loft.
Simply move the grouped loft along the axis back to its original position. -
@jgb said:
CL will fail on any one of the following most common conditions... (as well as a few others)
- 2 lines not joined at "endpoints" although they look like they do. Endpoints joined when "Constrained by" will not loft.
- a tiny fragment at an endpoint is taken as part of the perimeter CL finds, or you define by selection.
you keep saying this stuff but it's not curviloft which is failing..
unless you also consider sketchup itself is failing at creating a surface to my square in this scenario:
and your situation '2' is just poor user selection.. i'm not really sure what you're expecting the plugin to do in that scenario..
-
@yanosiento said:
guys, how could i make a surface from those contours? just a narrow face beetween the lines
http://s14.postimg.org/oebxw5ab5/d_vida.png
thnks
from the image you posted, it looks like all you would have to do is select all of it then use curviloft's skin contours function. (the 3rd icon in the toolbar)
-
If none of the preceding comments apply or fix your issue... then please attach a SKP to a post and we'll look at it...
It will be 'do-able'...
-
Jeff
You are being picky.
Of course the "fail to loft" is not a CL fault. It is the geometry faults that "prevent" CL from lofting.
-
Hello Fredo or someone who can help me.....
I have installed Fredo pluggins like Round Corner, Join Push Pull and curviloft on MACOSX 10.9.1 macbook pro 15" 2014 retina
When I use Fredo´s plugging Round Corner, Join Push Pull and curviloft the window with the different options and parameters are really, really small. Is impossible understand anything.
Can you help me ?
Kind regards
-
It's a known problem with retina displays...
-
Thank you very much Cotty.
I´ll be waiting for a solution....
kind regards
-
@oli_sketch said:
Thank you very much Cotty.
I´ll be waiting for a solution....
kind regards
You should share your details here, maybe it will help Fredo to find a solution ...
-
Hello,
This is my first post.I am having trouble skinning the curve that I have attached. Am I am doing something wrong?
I will appreciate any help.
I am running this on SU 2014 pro.
Thanks in advance. Appreciate all the help I can get.
-Sam
-
It is VERY faceted - several tens of thousands for potential facets !
The biggest 'arc' has 240 segments on its own...
Can you simplify the segmentation ?
-
Had some stray lines!
Also file is too large to load here see Dropbox link https://www.dropbox.com/s/xmtune9hovo9cqk/TestSkin11.skp used Fredo's Curviloft to skin and done using SU v8 -
TestSkin12.skpUsing TIG's suggestion reduced edges from ~670 to ~63 and used 'extrude edges by rails', as an alternative.
No noticeable difference, except model size is greatly reduced! -
Have a look at my post.
http://sketchucation.com/forums/viewtopic.php?f=15%26amp;t=56028%26amp;start=30
-
Hello TIG & mac1,
Thank you very much for replying. As it is obviously evident, I am a newbie at not only sketchup but also mechanical drawing.I have to sheepishly admit that I don't know what you mean by simplyfying the model or reducing the edges. How do I do that? If you can suggest some links I can read up on my own, and wont bug you guys with any more stupid problems borne out of my inexperience.
Thank you again.
-Sam -
A Circle or Arc has a number of segments.
These defaults can be seen in Entity Info [24 & 12 ?].
If the curve has not already been incorporated into a 3d form then you can adjust the segmentation for it there.
You can also change it as you create the Arc - e.g. type 6s +<enter> when you start the tool and the segment count becomes that.Each segment is used to create an edge in a 3d form, so the more segments you have the more extra geometry is made. This affects performance as there are shadow casting/receiving to be calculated and material/textures to render etc...
This applies to native tools and plugin 'surface makers'.
The Circle default is 24s, so if you extrude that with PushPull you end up with 24+24+24 = 72 edges and
24+2 = 26 faces.
That will look smooth enough for most purposes.
It it were a handrail reducing it to say 12s would still probably look the same with hidden-geom off...
12+12+12 = 36 edges and 12+2 = 14 faces - a significant reduction in unneeded geometry...
If you foolishly increase it to say 360 [1 segment per degree!] it'll look little different from 24s AND you'll have a staggering 360+360+360 = 1080 edges and 360+2 = 362 faces
SO when you draw lines/curves that might become 3d objects think about the edge/face count that might result as they combine...
Advertisement