[Plugin][$] JointPushPull Interactive - v4.8a - 30 Mar 24

BorgMan

By the by, I got this error when opening SketchUp. Does this help out?

TIG

By the by, I got this error when opening SketchUp. Does this help out?
That is most likely because you have not updated to SketchUp v2014M1 which fixes a known issue.
In SketchUp v2014M0 PC if you launch SketchUp by opening a SKP that is on a drive other than the drive where SketchUp.exe is located then it messes the S: list.
Thus the Ruby2 stuff never gets loaded and tools like the SCFapi that rely on some functions fail.

You should find that starting SketchUp from the menu and then opening a SKP does NOT create this issue.
There is a fix rb file that went into Tools and sorted the $: out, BUT simply installing SketchUp v2014M1 is advisable, as it also fixes a few other glitches under the hood.

cosmorobus

not selected polygons. What's the problem?
I have
Fredo6_JointPushPull - v3.2b - 17 Mar 14
LibFredo6_v6.0b
Sketchup 14.0.4900

interior_design

It is really helpful in modeling which gives more precise and flexible design, indeed.
Many thanks to the author: Fredo.

littleche

Hi

I have a problem with JointPushPull ...
As you can see in the picture ,I can not pull this face Properly.
The parts that I've marked with a green line ,JointPushPull is destroyed face .

What can I do to fix this problem?

1.5.jpg

JP&P.skp

Dave R

Well, to start with, you've got some reversed faces. Instead of fixing them, you've tried to mask them by making the front and back faces the same color. That's not the right way to take care of the problem. Correct the face orientation and try again.

Then try scaling up by maybe 100 to avoid smaller faces.

Box

Apart from the reversed faces that Dave has pointed out, you have a layer other than Layer0 as the active layer, always keep 0 active, keep all raw geometry on Layer0 and only place groups or components on other layers. Also your linework is bad. Your edges are rough and don't form clean curves.

Dave R

Indeed! And as is typical of computer stuff, GIGO applies here.

Box

Just a couple of examples to show you what you need to fix.

This whole section is twisted

The red circle shows where the edge is kinked without any corresponding geometry.

littleche

"Dave R" & "Box" Thanks for your help ...
revers and oriant face does not affect the performance of jointP&P plugin.

Yes, I agree my linework is bad but in bad line plugin good working !
I have tried many different ways But according to the your advice I still was not able to reach my goal.Another way to tell if it is possible ...

Is not this a bug in the plugin?

Dave R

It would be nice to blame the plugin because your bad line work is causing the problem, wouldn't it?

Box

It's not a fault with the plugin, it is attempting to follow what you have drawn.

Get everything on the same layer and clean up your geometry and the plugin works.
I've no idea how you drew it in the first place but perhaps it would be easier to start again and get the geometry right rather than trying to repair it.

littleche

This problem was solved! Thank you for your help ... my worklin was very bad .I got to practice tips that you said and Finally I drew a good workline with tools on surface plugin and jointpull&push It's nice to end.

and Again, thanks ...

09-27-2014 04-34-39 ب.jpg

Box

Well done.
Learning to get your structure right in the first place is far better for you than getting a plugin to work.

fredo6

NEW RELEASE: JointPush Pull Interactive v3.3a - 19 Oct 14

JointPushPull Interactive 3.3a is required for the support of usernames with non-ascii characters in Sketchup 2014

See main post of this thread for Download of JointPushPull.

Fredo

mvsuriano

Hello - I've been using the old version of JPP for some time - its awesome. Recently tried to install the newest version via SketchUcation tools in SU 2014.

I see the toolbar, however, clicking on any button/tool in the JPP toolbar doesn't do anything, it just defaults to the tool I had selected prior.

Any suggestions?

Thanks!
Mike

cotty

@mvsuriano said:

Hello - I've been using the old version of JPP for some time - its awesome. Recently tried to install the newest version via SketchUcation tools in SU 2014.

I see the toolbar, however, clicking on any button/tool in the JPP toolbar doesn't do anything, it just defaults to the tool I had selected prior.

Any suggestions?

Thanks!
Mike

Did you update LibFredo to version >=6.3? Are there error messages in the ruby console?

fredo6

@mvsuriano,

Could you open the Ruby Console before clicking on the JPP icon, in case there are error messages displayed

Fredo

mvsuriano

@fredo6 said:

@mvsuriano,

Could you open the Ruby Console before clicking on the JPP icon, in case there are error messages displayed

Fredo

HI Fredo - turns out I do have an error. I did update to FredoLib 6.3a prior to install. This is the error I get.

Error: #<NameError: uninitialized constant G6::ShapeGrid>
C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_JointPushPull/JointPushPullTool.rb:101:in initialize' C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_JointPushPull/JointPushPullTool.rb:64:in new'
C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_JointPushPull/JointPushPullTool.rb:64:in action__mapping' C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_!LibFredo6/Lib6Plugin.rb:133:in call'
C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_!LibFredo6/Lib6Plugin.rb:133:in launch_action' C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_JointPushPull/bootstrap_JointPushPull.rb:81:in launch_action'
C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_JointPushPull/bootstrap_JointPushPull.rb:128:in block in declare_command' C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_!LibFredo6/Lib6Plugin.rb:1080:in call'
C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_!LibFredo6/Lib6Plugin.rb:1080:in command_invoke' C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_!LibFredo6/Lib6Plugin.rb:1062:in block (2 levels) in build_config_commands'
C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_!LibFredo6/Lib6Traductor.rb:1077:in call' C:/Users/msuriano/AppData/Roaming/SketchUp/SketchUp 2014/SketchUp/Plugins/Fredo6_!LibFredo6/Lib6Traductor.rb:1077:in block in add_command'
-e:1:in `call'

Dave R

Try deleting the LibFredo6 files/folder from the Plugins folder and install the current version again. I had a problem due to some file not getting removed/overwritten when I installed the latest version. Deleting and installing fresh took care of it though.