Medeek Wall Plugin

medeek

Tutorial 54 - Stairs with Landings (13:27 min.)

medeek

With each landing being configurable, its possible to mix and match some of the landings:

medeek

First look at double landing configurations with 2-step and 3-step L-winders:

gullfo

that looks like a lawsuit just waiting to happen lol

medeek

Tutorial 55 - Complex Stairs</a> (9:57 min.)

medeek

Since I've been focusing on updating the stair module the last week I've had quite a number of requests for various things. One request is the ability to flare out the bottom of the stairs. I can add in this functionality however to start with it would be very rudimentary (just a modification to the treads and risers as shown):

I'm not entirely sure how one would go about in-fill framing the flared portion, nor do I think there is any established or standard way to do this, I could be wrong. Any thoughts or ideas in this regard? I should probably ask first if this is something that you would all want or even need.

medeek

First look at an inverted T-Shape staircase with a straight and a curved flare:

medeek

Here is a quick study of the three types of tread extensions that are probably the most common. I can probably make this happen but it will have a number of new parameters in yet another sub-menu.

With the half and full round, the riser simply follows the nosing dimension, however with the square cut extension the amount of the riser extension could be independent.

For both the full and half round the radius of the curve is paramount but also the placement of the center of the curve in the Y direction (perpendicular to the stringers). The extension variable can be used for the Y-dir placement of the curve.

The round nosing makes things a bit interesting but that can also be dealt with by breaking things down into a piecemeal modeling algorithm and then using some boolean addition of solids.

The parameters shall be:

Tread Extension Options:

Extension Side: Both, Left, Right
Extension Type: Square, Round, Half Round
Tread Ext. Length: 10" etc... (this variable also sets Y placement of center of curve)
Riser Ext. Length: 8" etc... (only applies to the square ext.)
Extension Radius: 10" etc... (only applies to full or half round extension)

I never get a day of rest, maybe after this update I'll move back to the Floor plugin...

medeek

If I enable some turn outs and volutes I will need to adjust for these but also I need to provide some additional parameters so one can fine tune the placement of the handrail and its termination:

medeek

So this is currently a specific limitation when it comes to handrails:

The issue here is that each run of stairs literally needs it own handrail sub-menu (set of parameters). Globally the handrail options are fine but as soon as you start adding landings you then have multiple stair runs and it quickly gets complicated. Note that the same handrail settings get applied to each run of stairs currently, this is less than desirable with complex stairs.

Of course the workaround for this is to not rely on the automatic landing functionality and create each separate run of stairs as a separate assembly (linear stair runs only). However this negates the convenience of having the landing and winder options that I recently added.

Yes, I’m a bit in the weeds now but I want this new handrail system to be as functional and fully featured and efficient as possible. I will need to put on my thinking cap and come up with a viable solution that is not too complicated (for a complex problem).

gullfo

one option might be to have the handrails independent of the riser sections. you could create a stair assembly from whatever your stair setup is (like a component with unified stair metadata inside it), then add the handrails over the entire structure - which could be a continuous rail or segmented, etc. might be easier to code it this way by reading the overall stair assembly metadata and use that to generate the handrails.

medeek

Version 3.7.9 - 12.26.2024

Added the inverted T-Shape landing.
Enabled straight and curved flared staircases.
Added 37 handrail fittings into the built-in handrail fittings library.
Updated the handrail module with additional parameters for over-the-post handrail systems.
Enabled additional handrail sub-menus for multi-landing stair assemblies.

medeek

Tutorial 57 - Over-the-Post Handrails and Fittings (18.42 min.)