Need help using Shape Bender
-
You should get a better result if you rotate the component around so it's inline with the red axis.
The position and length of the straight line in relation to the piece to be bent is critical. In fact the relative positions of all three pieces affect the result considerably.
-
ahhh... Ok I see.
-
Thank you. I really got it all wrong. Mea culpa. (Although I have to admit that I am kind of glad there is not a lot of stuff I am bending. Nothing intended, but the workflow is strange here.)
-
What do you mean by the "workflow is strange"?
I don't see anything strange about using Shape Bender. It works as described. Does what it says on the label.
-
I have to say.. I've never gotten it to work reliably either. and yes, I've watched the video. tho I think thats the problem. it's a video.... trying to follow step by step instructions in realtime is a bit of a sod at times. (ok do this that..hey wait what was that, rewind, no to far, no, missed it.. argh - a typical scenario for me.. )
maybe someone can do a series of step by step written instructions for those of us that can't follow videos that well? eg in the video for this it wasn't clear that they have to be on the same axis.. until chris said it here....
-
I think it was covered in text in the Shape Bender thread.
-
Mine never finished bending... Not sure. maybe my computer is too slow for the complex geometry. maybe I'm still doing something wrong.
-
I'm not sure of the exact shape you want to achieve, but try this, if it doesn't work then it is your PC.
-
@krisidious said:
Mine never finished bending... Not sure. maybe my computer is too slow for the complex geometry. maybe I'm still doing something wrong.
Did you try it in the file I returned to you? That had the correct setup and worked for me.
-
I am new to posting in here, but I am having an issue with the Shape Bender plug in. I am trying to bend this railing insert around a curve. I keep getting hung up when it gets to part 2 of 5, 6% while it is trying to explode 32 objects which seems to be the second time it says 2 of 5. I read some of these threads and tried scaling it up by 100 and even 1000 as that seemed to work for some people. I know it may be a complex file to bend but I got another railing of similar detail to work. Let me know if you need any more information and I have attached (or attempted to) the file to work with. Let me know if you know whats going wrong. Thanks.
-
There is no file or image...
-
I was afraid that was going to happen as it was being funny when trying to attach. It keeps "thinking" when I try to attach it. It is a 28,748 KB file. But I do not know the max file size that can be put here. What photos would you want to help? Ill add a screenshot to get us going, but I do not know why the file wont attach nor what photos would help if any even would. I feel like you really need the file to play with to say anything.
-
It does look incredibly intricately detailed.
For sure if it's at 'normal sze it'll be trying to make tiny facets and will fail when they fall below SketchUp's 1/1000th inch toleranace - which is usually enough for building space-rockets
Try scaling everything by x100, do the bending and scale down by x1/100 again...
Try x1000 etc if it still fails...
There are limits to what SketchUp can make - 1/1000th inch long [short!] edges and small facets etc...
These can exist in SketchUp [e.g. after scaling down again], but they cannot be made initially. -
And on top of Tig's advice, you may need to wait for it, it's a lot of work for the bender to do. You never know, leave it overnight and when you get up in the morning it could have finished.
And you can't upload a 29 Mg file, I think the limit here is 5mg, maybe 10. -
It WILL take a while to bend it... be patient...
Uploads are limited to <=~4Mb...
You can ZIP files to get them as small as possible...Although it looks complex that size seems excessive...
Have you used Model Info > Statistics > Purge Unused... ? -
As I mentioned in my earlier post I did try to scale it up by 100 and by 1000 and neither worked. I may let it run overnight and see what happens. Last time I think I got a bugsplat after quite some time but ill give it another shot. and no I have not purged it...Another thing to try. Thanks Ill let you know what happens.
-
It's hard to tell from the oblique angle in your screen shot but the thing looks like it is symmetrical. You could cut it in half down the centerline and bend only the half. That would cut the entity count roughly in half and maybe speed up the bend. Then copy the resulting component, flip it and move the copy into place.
-
I need help please! I have used shape bender before (successfully)to create roadways with a 3D alignment file, but this time it does not seem to be working. I have my file below (link to dropbox)- my base model (roadway section, at the correct length) is to the left, the alignment "curve" is to the right. I have my horizontal line parallel to the base section (3' to the left of it)
I have gotten it to the point of preview, but the preview when it does try to create the bend, it's not curved, and just strange, looks like it's up in space (however, there is another preview in red and blue colors that seems to be correct, but when I hit enter; it created the more geometric, strange one. It also has on a few occasions changed my orientation (start and end at opposite locations)
Please let me know if you can help, I need to have this in a couple of days (rendered)
***Let me know if the link below does not work
-
Use the arrow keys to change the selection.
-
There's an awful lot of geometry, some of it is not needed. For example, in the gutter areas, there are a bunch of coplanar faces that don't need to have edges dividing them. You probably don't need as many segments in the curves, either. All that geometry is going to make SketchUp work hard and probably take a while to process. Another problem is that you've got some reversed faces. Those ought to be repaired and maybe affecting Shape Bender.
You could use Follow Me for that curve too.
Advertisement