Hi everyone.
I want to make Coffered Slab to my floor.
Is there any plugin to make this. ?
Or is there any way to make this easyly ?
Thank you.

http://img696.imageshack.us/f/82270838.jpg

Hello. I have got a problem.
I create my project. It has got 2 Floors. I use "Push/Pull and raise each one.
Then, I put them one after the other. When I delete exterior floor line, some lines get lost interior.
How can I solve this problem.? Is there any way to make it.?
(Plans are from Autocad.)
Thank you.

No way ?

Hi everyone.
How can I see my drawing 30, 60 Degrees perspective?
Pls help me.
Thank you.

@tig said:

Push/Pull the building up/down. Perhaps leave it a little higher/lower than you intend it to be finally [depending on whether it is to be built up or cut in]... Afterwards you can always Select the building AND its flat stamped area (you can vary the offset of that flat area at the time of stamping by typing a new distance into the VCB) and by then using the Move Tool on this Selection: constrained vertically (blue) with Shift-key: then all connected geometry like 'embankments' will adjust their angle to suit...

Thank you but I dont understand generally.
Can you explain with pictures... ?

Hi everyone.
I want to write my problem on this title.
I have a problem with Sandbox.
I creted my land with your help. I want to put my building to the levels.
I know, we use "Stamp" for putting building on levels. But I didn't write numeral value for determine the building how much deep or up.
How can regulate that.?
Thank you.

Hi everyone.
Firstly thank you for your helping.
I create my land with useing my topo lines.
I have got another question.
Now, i want to put my building on this land. But my building will stand levels.
How can i put my building on its levels.?
When i try to put my building on my land, building's door and windows stand underground.
Can you show me a way for solve this problem.?
Thank you.

Hi again.
I make what did you say thank you.
I create my buildings Make Group one by one.
But my computer die me so it works very slowly.
And there is a problem there. When I use STAMP for my building, sometimes they come out my roads.
You can put my buildings backward of the roads.
Can you put my building on my land for me and can you check it for me.?
I send my file.
Thank you.

http://rapidshare.com/files/303724169/Land.skp.html

Hi again.
I watched the videos of sandbox.
I put my roads and house's lines but I dont puss/pull them.
It is not let me puss pull my houses.
How can i do that?
Thank you.

Yes, you are right. I will change it with their slopes...
Thank you for your helping...
See you later.

Thank you for your answer. I try to do it.
But I want to see my difference of levels and i want to give my roads their slopes.
So when I look my site plan i will see my topo lines and my roads.
First file my topo lines, second file is my roads.
Can you make something for me.?
Thank you.

http://rapidshare.com/files/302778050/Topos.skp.html

http://rapidshare.com/files/302779481/Roads.skp.html

@tig said:

Sandbox Drape Tool or Stamp Tool.

Can you show me an example, how can i do that please. ?
(I want to make my topo lines like stairs over and over on my 3d drawing. But I want to put my roads on this topo lines with slope. (I want to put my roads horizontally.)

Thank you.

Anyone help me please ?

Thank you for your helping...
I have got another question. I want to make my topo lines like stairs over and over on my 3d drawing. But I want to put my roads on this topo lines with slope. (I want to put my roads horizontally)
Is there any way to create this ?

@tig said:

Here's a simple tutorial on doing it 'manually'...[attachment=0:4f87m8ih]<!-- ia0 -->CONTOURS.skp<!-- ia0 -->[/attachment:4f87m8ih]

Can you make my project ?
It is very hard for me... ?

This is the new one...
Firstly I puss pull only my topo lines...
And then I want to put my ways on these topo lines...
I send my topo lines project and my ways...
Now, how can i do that ?
(I only puss pull my topo lines, i didnt use Sand Box. Because I tried it but i didnt success it.
Thank you.

http://rapidshare.com/files/301347057/New_Topo_Lines.skp.html

http://rapidshare.com/files/301349010/Ways.skp.html

i dont try it... How can i do my project with this plugin... Can you help me pls...
I dont know how can i do that... ( Slopes, way etc...)

I want to send up my land but how can i do that ?
I have got lots of slope and ways...
Is there any way to do that ?
I send my drawing...
Thank you for your help...

http://rapidshare.com/files/301138348/1.skp.html

Thank you for your answer.

Just think about floor. Look at second picture. The walls is 20 cm , but floor is just line. ?
Floor must be 20 cm.

Where did I wrong while I was drawing ?

Hi everyone.

I try to build a house.
I extrude the walls and made Component but when I look the floors there is no floor covering there.
On the second picture, there is a section and floor covering.

What can you say me for this problem ?