Does anyone have...
-
for skateboarding ... of course!... why waste it by putting water in there?
surface = 2 layers of 1/2" ply then a final surface of 6mm Finland birch
-
12 inch ?
in 2011 there are always these sortes of measures?
That is completely incongruous!
Decimal system don't penetrate in the new world?
-
1/2" is 'half' an inch ~12.7mm
So 12mm ply in EU/Rest_of_the_World == 1/2" ply in USA... -
A quick way of converting imperial fractions to metric is....
1/2" = 16/32" (Change to 32nds if possible)
Multiply 16 by 8 ( 16 * 8 = 128)
Put in a decimal at one decimal place
so 128 = 12.8mm
It.s an approximation but a pretty close one.
Boring message over
-
Sweet model Jeff!
How did you make the bowl shape(the negative space)? ...is it mathematically generated?
-
@unknownuser said:
12 inch ?
in 2011 there are always these sortes of measures?
That is completely incongruous!
Decimal system don't penetrate in the new world?i admit, metric makes way more sense.. i guess we're (americans) just stubborn? or too lazy to switch?
@tig said:
:roll:
1/2" is 'half' an inch ~12.7mm
So 12mm ply in EU/Rest_of_the_World == 1/2" ply in USA...our 1/2" is actually 15/32" which is really close to 12mm (11.9mm)..
just easier for us to call it half.23/32 = 3/4" ply
19/32 - 5/8" ply
etc.a big box store here in the u.s.:
http://www.lowes.com/pd_12227-99999-LBR12227_0__ -
What !!!
The USA has [slightly] thinner plywood than the rest of the world ??
Let's all agree to call it '12mm'
Did you make the model out of Slicer cuts or ModelSlicer ?
I have a project on the backburner to make a Slicer+Slotter using components in the assembled set and flattened...
-
Plywood is almost always thinner than the dimension it is called but then so is all other wood. A 1x6 will be 3/4 in. thick by 5-1/2" wide. If you want one inch thick lumber you have to buy 6/4 and surface it.
-
@d12dozr said:
Sweet model Jeff!
thanks
@unknownuser said:
is it mathematically generated?
i guess you could say that
-
@tig said:
What !!!
The USA has [slightly] thinner plywood than the rest of the world ??
Let's all agree to call it '12mm'haha.. i can imagine this jobsite scenario
me - "hey, buddy, bring me a sheet of that 12mil"
him -" uhhh "@unknownuser said:
Did you make the model out of Slicer cuts or ModelSlicer ?
I have a project on the backburner to make a Slicer+Slotter using components in the assembled set and flattened...all solids then boolean actions.
-
v#
or 
-
@unknownuser said:
v#
or 5 is the only version available to me.. all osx development is strictly focused on that version now.
so
(still a lot missing though.. no plugins yet.. the UI needs a lot of improvements still.. but, most if not all of the drawing functions work and they're mega powerful ) -
My converter
gives that
and you said that must be
@unknownuser said:
1/2" is 'half' an inch ~12.7mm
there is 0.3 mm on the fly !
The sawdust?@unknownuser said:
each one of those squares = 12"
So the square of Jeff 12" must be 30.5 cm or 30.48 cm ?
-
@unknownuser said:
So the square of Jeff 12" must be 30.5 cm or 30.48 cm ?
any way we call it, that's still an awful lot of cardboard!
-
-
@unknownuser said:
i guess you could say that
Ha...Nice, that makes sense because its so hard to reliably make something like that in SU that corresponds to real-world requirements
-
@tig said:
Did you make the model out of Slicer cuts or ModelSlicer ?
I have a project on the backburner to make a Slicer+Slotter using components in the assembled set and flattened...can't wait for that
-
As I said it's on the "backburner" - it's item #9 today - but it was #8 last week !
-
I'm still excited. I can wait u out. 
-
@unknownuser said:
for skateboarding ... of course!... why waste it by putting water in there?
I don't think you have a choice, Jeff. Doesn't it ever rain in NYC...?
Beaut model though!!
Advertisement