An exercise: DRAWING A PARISIAN FENCE

pilou

Seems this 2 components sufficient?
As it's 3D volumes, you can flip vertically the second components for have all possibilities! (front / back)
click image

Don't know how are the bottom and finished sides?

simon le bon

Hi Pilou

Decompose into these two basic components seems a good idea.
This way we can work with some simplicity on the problems of overlapping sinusoids. We can may be at the end use yours to make the component I was primarily thinking of in order to avoid any pb of seams

@unknownuser said:

Don't know how are the bottom and finished sides?

close up

Remain to draw these curved and angled sinusoids..

@+ s

TaffGoch

Simon,

Consider how the manufacturer produced the fence. Q: With what did they start?

A: A length of "wire," with a constant, repeated sine wave. This should be maintained in a 3D model. Keep all of the sinusoidal segments the same length.

Truly, the sine segments along the top of the fence will be curved, but they should be maintained at the same length. I can demonstrate this evening, when I have some modeling time.

-Taff

ely862me

@taffgoch said:

Simon,

Consider how the manufacturer produced the fence. Q: With what did they start?

A: A length of "wire," with a constant, repeated sine wave. This should be maintained in a 3D model. Keep all of the sinusoidal segments the same length.

Truly, the sine segments along the top of the fence will be curved, but they should be maintained at the same length. I can demonstrate this evening, when I have some modeling time.

-Taff

So true..i just quit because of that .

ely862me

When i thought i have figured it out ,disaster(see how the wires intersect in the left down corner and ..of course ,they are not woven)
Ex Fen.jpg

More trials to go .

pilou

@unknownuser said:

Remain to draw these curved and angled sinusoids..

When you have flat model
Curved can be made by the Fredo Scale, no?

ely862me

hmm..just..wow..clearly u know some maths .

simon le bon

Wahoo! "bravo" Taff _ and I feel the result beautiful

Now I know it can be done, I want to find the way: with your indications but without open your skp yet.

and I'm actually in front of the picture expecting something stand up from my perplexity

I shall come back

*simon

TaffGoch

@simon le bon said:

...and I'm actually in front of the picture expecting something stand up from my perplexity

Simon,
As I wrote earlier, I had a couple of false starts, until I studied the picture more closely...
Wave counting...
Each unit/increment is half of a sine wave (crest-to-trough, or trough-to-crest.) I finally recognized that each diamond was 6-units wide, having 5-unit side lengths. Only then would model components fit together properly.

-Taff

broomstick

@simon le bon said:

I know it's not the subject of this thread, but that image would make a great map with an opacity mask on it

Gaieus

True, I was also thinking about it. You can easily make it tilable horizontally, too - the only problem is that vertically it should be a bit higher so that you could apply it on more various (although of course, still limited) height.

simon le bon

Dear Taff,

I go slow, step by step. It is so cool to get you as professor

1)how to make a sine-wave.

2)anatomy of the braided fence
Re I see 6 but not 5 1/2 sine-waves:?:

OK we'll see later!

3)some testing just to see!

..to be continued

simon

simon le bon

@ely862me said:

Mr Simon,watch it, because they are now weaving.

Ely, I don't understand what that means..

Well: there is a problem with my previous test.
If I use 6 by 6 half waves as shown, the wiring doesn't braid!!!

let me see...
*s

ely862me

Mr Simon,watch it, because they are now weaving.

Edited:Mr Simon,watch it, because they are NOT weaving(braiding). (sorry not so usual words for me )

ely862me

I meant it s not braiding.
U must follow the indication from Taff : 5 by 6(diagonal)

p fence.jpg

simon le bon

Taff, you are right!
And Ely too (you are quicker than me )
The diamond need to be done with an odd number of semi waves.

If I take the same wave and use 5 semi waves:

that works perfectly.
if I analyze better the fence -( I take a pen an a shit of paper and draw the wave blindely, just looking to the picture, i discover you are right: 5x5 semi waves!)

A good point
going to next step..
simon