Medeek Wall Plugin

medeek · 27 Jun 2018, 00:34

Version 0.8.1c - 06.26.2018

Fixed a bug where wall corner trim thickness equals trim width.

This will now allow the user to specify a 1.5" x 1.5" interior corner trim.

medeek · 27 Jun 2018, 17:49

Just about to wrap up the beam tool this morning and then I got thinking about the end treatment of beams:

I don't know what the technical term is for this but I call it the Start Cut and End Cut of a beam.

There could be any number of possibilities for the end cut profile:

I think I will just start with two options:

None
45 deg (to mid height of beam)

Charlie__V · 27 Jun 2018, 18:58

@medeek said:

Version 0.8.1c - 06.26.2018

Fixed a bug where wall corner trim thickness equals trim width.

This will now allow the user to specify a 1.5" x 1.5" interior corner trim.

Thank you Nathaniel, this resolves the issue.
And for the sake of clarity as to what the description means/is.....see pic below

medeek · 27 Jun 2018, 19:43

@charlie__v said:

@medeek said:

Version 0.8.1c - 06.26.2018

Fixed a bug where wall corner trim thickness equals trim width.

This will now allow the user to specify a 1.5" x 1.5" interior corner trim.

Thank you Nathaniel, this resolves the issue.
And for the sake of clarity as to what the description means/is.....see pic below

Thank-you for providing the additional clarification.

Inevitably I'm going to miss things, didn't even consider a square corner trim on an interior corner, funny thing is I've seen this sort of thing a million times though.

Please keep sending in the bugs and feature requests, I know there is more out there. Please also post up your models you create with the plugin I am curious as to how the plugin is actually being utilized.

Bob James · 27 Jun 2018, 20:54

I know this sounds somewhat heretical but how about an option to set the full version to match the lite version for the times when all that's initially needed is a concept drawing?
Or is it obvious how to do it?

medeek · 27 Jun 2018, 21:16

@bob james said:

I know this sounds somewhat heretical but how about an option to set the full version to match the lite version for the times when all that's initially needed is a concept drawing?
Or is it obvious how to do it?

Within the global settings under the Wall Tab you can set the default framing mode to one of the three options. This will then always bring up the wall draw tool with the selected mode, while still giving you the option to bump the wall to any of the other modes if you suddenly need to see the framing.

Bob James · 27 Jun 2018, 22:09

Thank you

medeek · 28 Jun 2018, 21:41

Version 0.8.2 - 06.28.2018

Added the ability to draw and edit beams with the Beams/Column Toolset.
Glulam, PSL, LVL, LSL, Timber and Lumber beam types added to the beam module.
Start and end cut options (miter,firecut) added to the advanced options for beams.

View model here:

3D Warehouse

3D Warehouse is a website of searchable, pre-made 3D models that works seamlessly with SketchUp.

(3dwarehouse.sketchup.com)

Bob James · 28 Jun 2018, 22:03

Could you add the revision number to the rbz file?
medeek_wall_ext 0-8-1c.rbz
medeek_wall_ext 0-8-2.rbz

medeek · 28 Jun 2018, 22:12

@bob james said:

Could you add the revision number to the rbz file?
medeek_wall_ext 0-8-1c.rbz
medeek_wall_ext 0-8-2.rbz

Yes, that is probably not a bad idea.

medeek · 28 Jun 2018, 22:13

Trying to find a decent wood grain to use for timber beams, any suggestions or images anyone is willing to share? I've got a decent end grain image, just looking for the side grain.

P.S. I am also looking for a good pressure treated texture/material.

medeek · 29 Jun 2018, 05:51

The currently available beam types are:

Timber
LSL
Lumber
Glulam
LVL
PSL

The number of plies can be 1, 2, 3, and 4

Glulam species are currently Western Species and Southern Pine.

SCL lumber (LVL, LSL, PSL) are the US industry standard sizes (Weyerhauser, Boise Cascade, Louisiana- Pacific).

The miter cut puts the diagonal facing the bottom, the fire cut puts the diagonal facing the top.

3D Warehouse

3D Warehouse is a website of searchable, pre-made 3D models that works seamlessly with SketchUp.

(3dwarehouse.sketchup.com)

The materials shown are the default (built-in) materials for the plugin if the materials option is turned on. I'm not totally in love with the various textures I have for LSL, PSL, LVL and Timber but it is better than nothing I suppose.

For the timber and LVL option you can see that the end and edges have there own material assigned. Also if you apply a custom cut (after the fact) the way I have the materials assigned should allow you to maintain the proper end grain appearance.

The only thing really missing is steel beams which should not be too big of a leap now that I have the whole beam system/module in place.

Tomorrow I will jump back on the garage door module and see if we can make some headway with that.

medeek · 29 Jun 2018, 07:27

One last thing to note with the beam module is that all of the standard sizes are US/Imperial.

I can add in standard sizes for metric however I will need that information. I currently have glulam beam data for the UK, South Africa and Australia but I will also need PSL, LVL, lumber, timbers and LSL.

medeek · 29 Jun 2018, 12:19

Version 0.8.2b - 06.29.2018

Steel: Wide Flange (W) beam types added to the beam module.

I've only added five wide flange sizes thus far. I just need to know what sizes are most typically used and I can add them in.

Note that miter and fire cuts work with the steel beams as well.

I was also thinking an advanced option for steel beams might be a nailer plate on top and/or bottom of the beam, again feedback in this regard will determine if I pursue this further.

Another thing to note with beams is that you can move them around just like any other object in SketchUp using the SU move tool, unlike the walls. Technically you can move the walls with he SU move tool as well its just they won't stay connected if you do.

Another advanced option for beams would be a hanger library which can be added to or modified by the user. I am already doing this sort of thing for window and door components so it isn't a big stretch for beam hangers.

medeek · 29 Jun 2018, 23:05

Version 0.8.2c - 06.29.2018

Added a hanger library (customizable) and the ability to place hangers at the start and/or end of a beam.

Hangers shown are: HU612, LUC26Z and LUS26

The hanger library is located in the "hangers" sub-folder of the library folder of the plugin.

I have a few Simpson Hangers included but any of these can be modified and additional SKP files can be put into this folder. The plugin will automatically allow the selection of any components found within this sub-folder when selecting hangers for beams within the draw and edit menus.

I have contacted Simpson Strong-Tie in an effort to get a few more of their more common hangers that I can then simplify and include in the plugin. I am particularly interested in the HUCQ series.

In order to minimize polygon count I typically eliminate most of the holes in the hangers and also any curved surfaces, the goal is to keep the file size below 50 kb if possible.

I should also add that one could also include column caps in this sub-folder, like the CCQ/ECCQ/ECCLQ/CCTQ series.

medeek · 30 Jun 2018, 08:08

@bob james said:

As of 0.8.2c the only thing in

C:\Users\Bob\AppData\Roaming\SketchUp\SketchUp 2018\SketchUp\Plugins*medeek_wall_ext\library*
is one window and one door. : :

You'll need to download 0.8.2d, I'll roll it out tomorrow.

Bob James · 30 Jun 2018, 08:43

As of 0.8.2b the only thing in

C:\Users\Bob\AppData\Roaming\SketchUp\SketchUp 2018\SketchUp\Plugins*medeek_wall_ext\library*
is one window and one door. : :

Bob James · 30 Jun 2018, 08:45

The Hangers are in the 0.8.2c Library.
I was looking in 0.8.2b
My mistake: sorry

Charlie__V · 30 Jun 2018, 20:41

Re: Wainscoting feature/suggestion
Pretty common to have a "band board" in SE USA (sometimes called "water table").
Perhaps your wainscoting code could be adapted to create the band board and possibly a freize board as well.(please see pic & SU model)
Having it automatically cut out for door openings/etc. would be quite handy.

......merely a suggestion.

BandBd_WaterTable_06_30_2018.skp

C

medeek · 30 Jun 2018, 23:27

Version 0.8.2d - 06.30.2018

Created a number of low polygon count Simpson Strong-Tie hanger and column caps.

The full list of included hangers and column caps can be found here:

Medeek Design Inc. - Medeek Wall Plugin Vendors

(design.medeek.com)

Any hardware included with the plugin are custom drawn by me to reduce polygon count and standardize layers and materials.

If you would like to see specific hardware added please email me the manufacturer, part numbers and reference material. For Simpson hardware I typically refer to their literature and their various DWGs files found on their website.