3D Truss Models

medeek

Enabled metal plate connectors for floor trusses.

View model here:

https://3dwarehouse.sketchup.com/model.html?id=ec5402ad-0916-46f7-a84d-1bf7e57ed30f

The algorithm for the plate placement is fairly complex but not nearly as bad as I thought it would be, just knocking out some low hanging fruit while I'm recovering. The painkillers have kept me a bit off my "A" game so I haven't tackled anything big yet, like the completion of the stepdown hip truss set.

medeek

Looking through some old plans I've managed to dig up I came upon a couple of designs by another engineering firm.

Typically when I've dealt with truss designs I always seen a scarf cut on the bottom chord with the top chord remaining un-notched. In this other example the bottom chord is kept intact and the top chord is scarf cut or notched, while still allowing a continuous section to extend for the overhang with a depth equal to at least 1/2 the top chord depth. I think the picture below explains this far better than I can with words:

For MPC trusses I am used to seeing a 1/4" butt cut, however for timber trusses what is more appropriate?

Which method above would go with (arch. and structural reasons)?

View model here:

https://3dwarehouse.sketchup.com/model.html?id=6d3633a4-3b5c-4b9f-9780-23be5230c66d

medeek

Plates applied to the top truss:

Specs:

Truss Type: King Post
6x10 TC, 6x8 BC, 6x6 kingpost
Plate thickness = 0.25"
single row of bolts with two bolts per row.
connector plate width = 4.0"
Bolt Dia. 3/4"
Bolt Edge Distance (timber) = 4.0"
Bolt Edge Distance (plate) = 2.0"
Bolt Spacing = 4.0"
Bolts and Washers not shown.

View model here:

https://3dwarehouse.sketchup.com/model.html?id=ed8f688c-a1a2-4c2a-b09a-8ee937060922

medeek

This particular joint on a gambrel attic roof I am finding particularly difficult to plate:

Luckily I have a few samples to use as guides. Given my web configurations at this joint this seems to be the most reasonable method to plate this joint. Note that the plate should touch the interior corner and the exterior of the lower top chord but at the same time not project past the lumber into the spaces. Also the plate is rotated so that it is parallel to the upper top chords pitch.

The algorithm I devised to do this is quite clever I think but can be boiled down to a few concise lines of code:

  # Plate 2 (Gambrel Left)

	x2 = @W2x2 - (mpcyy)/(sin(@Phi2))
	y2 = @W2y2
	m2 = tan(@Phi2)

	x1 = @X2
	y1 = @Y2
	m1 = tan(@Phi1)

	x0 = (y2 - y1 - m2*x2 + m1*x1)/(m1 - m2)
	y0 = y1 + m1*(x0 - x1)

	xoffset = (mpcxx/2.0)*(cos(@Phi2)) + (mpcyy/2.0)*(sin(@Phi2))
	yoffset = (mpcxx/2.0)*(sin(@Phi2)) - (mpcyy/2.0)*(cos(@Phi2))

	mpcx = x0 + xoffset
	mpcy = y0 + yoffset
	mpcrot = -@Phi2
	MedeekMethods.metal_plate mpcx, mpcy, mpcxx, mpcyy, mpcrot, "PLGL"


	# Plate 2 (Gambrel Right)

	mpcx = @X5 - mpcx
	mpcy = mpcy
	mpcrot = @Phi2
	MedeekMethods.metal_plate mpcx, mpcy, mpcxx, mpcyy, mpcrot, "PLGR"

This joint has been the most difficult so far, everything else has been cake.

medeek

Version 1.7.4 - 12.20.2016

Enabled metal plate connectors for gambrel attic trusses.

View model here:

https://3dwarehouse.sketchup.com/model.html?id=5297dc32-fe7a-4bdc-bab2-ccadba5e5147

Frederik

Merry Christmas to you as well, Nathaniel!

medeek

Version 1.7.5 - 12.24.2016

Enabled metal plate connectors for valley truss sets.
Enabled materials and custom layers for valley truss sets.

View model here:

https://3dwarehouse.sketchup.com/model.html?id=9a6c9bc0-bf0d-4181-a54c-ac2257aed4f1

Merry Christmas to all.

medeek

Version 1.7.6 - 12.26.2016

Enabled metal plate connectors for monopitch trusses.
Enabled materials and custom layers for monopitch trusses.

View model here:

https://3dwarehouse.sketchup.com/model.html?id=40819b39-458c-4e87-8a5e-fe16982dfe1d

I just realized that raised heel option does not work fully with the materials and connectors, I will work on a fix later today to sync that up.

medeek

Version 1.7.7 - 12.31.2016

Enabled materials and custom layers for gable, hip, shed, TJI and dutch gable rafter roofs.

medeek

Version 1.7.8 - 01.02.2017

Enabled materials and custom layers for gable dormers.
Added advanced options for gable dormers, enabled exterior wall sheathing option.

View model here:

https://3dwarehouse.sketchup.com/model.html?id=5b255dad-4823-450d-a7d9-153d983e73a5

medeek

Out of curiosity when you architects and designers add hardiplank siding or other types of siding to a building what do you typically do? One could go so far as modeling the sawtooth/washboard of the siding but this would become very heavy in the model. I'm assuming most just use a material/texture to simulate the effect.

On a slightly different note I am looking for a really good texture to use for concrete in my other plugins, any suggestions?

medeek

This is an example of custom layers and materials implemented in the Medeek Truss Plugin and Medeek Foundation Plugin and used in one model:

View model here:

https://3dwarehouse.sketchup.com/model.html?id=5ff9d1dc-7384-4c7f-bc8a-915c2cd3fc6c

Turn off the sheathing layers first to reveal all of the structural framing etc...

Regular walls were created with the Housebuilder plugin.

The trim tool in the Truss Plugin was used quite successfully to manually trim back the dormer roof framing and sheathing.

medeek

Neck is doing pretty good these days, a little sore some mornings but nothing a little Ibuprofen can't fix.

On the flip side I came off of the Hydrocodone (for the neck and shoulder pain) about two weeks ago but still suffering from the withdrawal symptoms from this drug. My advice, don't ever use Hydrocodone unless it is absolutely life or death, its just not worth it.

I'm trying to figure out what to tackle next.

pbacot

All looking great! Glad your neck is better. (I don't know what you've got or what you've been doing about it: I used exercises on mine which seemed good, along with general exercise. And I use a foam neck pillow. Just in case you're looking for ideas.)

medeek

Tonight I spent some time trying to do some "real world" modeling and it quickly becomes apparent how limiting the plugins really are. Take a look at this model here:

https://3dwarehouse.sketchup.com/model.html?id=10e6822c-6ce1-4588-9d5b-56436b49750a

I need the ability to cut holes in the floors and insert headers and double up joists etc...

There is a serious need for a good staircase plugin, but maybe that already exists, either way it would be handy to have that part of the truss plugin or wall plugin.

Where roofs merge into other walls requires some attention.

I really need to get to work on the wall plugin, I'm using Housebuilder but I have a lot of features I would like to see to make it more flexible and reliable.

The double glulam beam rafter roof would be a nice addition as well.

medeek

Fixed a small bug in the valley truss set, hence the revision 1.7.8b. Hopefully tonight I can attack the timber truss module, I think I have most of the pseudo code put together.

Garry K

My stair maker plugin creates straight and curved stairs. Also Spirals.

straight stair.png

I am intending on adding quarter and half landings and some other features.

curved stair.png

I have built more than 200 of these geometric stairs including elliptical, specialty winders etc.
We also specialized in framed up curved stairs without the cost of stringers.

Some of my stairs projects include providing the bending forms and flattened stringers.

medeek

Spent some time this morning traversing through the common truss code updating some of the truss types so that I can enable energy/raised heels for all common trusses as well as enable custom layers, materials and connector plates.

As I've developed the plugin and added new features I used the fink truss as the cutting edge, so everything having to do with this truss type is pretty much up-to-date, however some of the other truss types are seriously lagging so a little house cleaning is in order.

It may be a few days before I can release this latest version since there is a lot of tedious work ahead.

pbacot

Great work. I wish I had your dedication!

medeek

I will download your stair plugin and give it a go.

That whole spiral staircase thing looks like a real challenge to code, don't even want to go there.