Grand Tetons: Fredo's Topo Shaper
-
Winner
-
Wow, Gus:
Excellent work. You certainly put that plugin to work.
By the way, is that "ACME APEX" Premium Quality Duct Tape on that cord jack, or just your run of the mill quack tape?
-
Jaw drop! awesome, great plugin
-
-
Gus,
This is a impressive example and I am glad to see it seems to work.
And thanks for describing the whole process. In my first design, I assumed the starting point would be clean contours with elevations. Then I realized that a large part of the workflow was about cleansing the contours from the DWG import and I introduced the cleanser.
Now, I think I should maybe think about adding a tool to transform a flat contour map into an elevated contour set.Also, would you mind sending me the model of contours. On the picture, I see that you have some sharp slope breaks and flattish basins. Currently TopoShaper is based on linear interpolation, and the few trials I made for a more sophisticated interpolation to get more smoothing did not reveal productive (long calculation time and artefacts). But I could try again on your model.
Finally, if you don't mind, I'd like to refer to your thread about these beautiful Colorado mountains in the main post of TopoShaper to illustrate the possibilities of the plugin of less conventional terrains.
Thanks
Fredo
-
@unknownuser said:
Gus,
This is a impressive example and I am glad to see it seems to work.
And thanks for describing the whole process. In my first design, I assumed the starting point would be clean contours with elevations. Then I realized that a large part of the workflow was about cleansing the contours from the DWG import and I introduced the cleanser.
Now, I think I should maybe think about adding a tool to transform a flat contour map into an elevated contour set.Also, would you mind sending me the model of contours. On the picture, I see that you have some sharp slope breaks and flattish basins. Currently TopoShaper is based on linear interpolation, and the few trials I made for a more sophisticated interpolation to get more smoothing did not reveal productive (long calculation time and artefacts). But I could try again on your model.
Finally, if you don't mind, I'd like to refer to your thread about these beautiful Colorado mountains in the main post of TopoShaper to illustrate the possibilities of the plugin of less conventional terrains.
Thanks
Fredo
Thanks to everyone for the compliments.
Fredo, sure, you could use this as an example for your main post. I attached the topo here. The elevation intervals are 400 feet. The USGS map was based on 80 foot intervals at 5 each for a total of 400 feet for the thicker lines which was easier to create. That will result in some loss of details.
I was thinking about perhaps adding a feature where you could add a point for a sharp peak perhaps. Otherwise, increasing the grid to the max (anything close to 200) will result in sharper peaks. On the USGS maps the closest you'll get to a peak will be a small elliptical topo line at the top of the summit.
The Grand Tetons (Grand Teton National Park) are in Wyoming, just south of Yellowstone National Park. Other than that, great plugin. Another good thing about this plugin is that you can leave SU while it's processing and won't freeze up SU. Thanks!
Correction. Here's the correct topo. -
@mitcorb said:
Wow, Gus:
Excellent work. You certainly put that plugin to work. By the way, is that "ACME APEX" Premium Quality Duct Tape on that cord jack, or just your run of the mill quack tape?
Thanks! Forgot to answer your question. That's just supposed to be a weathered metal plug casing. From my Stratocaster model.
I know you were kidding. Was just testing TopoShaper to see if it could do an arch top. Close.
-
@unknownuser said:
Gus,
... Now, I think I should maybe think about adding a tool to transform a flat contour map into an elevated contour set.mmmmmm ... that would be just the maximum
cheers
-
Wow! That is fantastic! If there were any bugs in that plugin, I am sure you found them out. Great job!
-
@unknownuser said:
Gus,
Now, I think I should maybe think about adding a tool to transform a flat contour map into an elevated contour set.
Fredo
If you manage that, you will be a GOD
Advertisement