(Not) Blowout Preventor - Oops
-
-
Almost done.
How do I get rid of the lines on top of the gas cylinder? (right hand side of the assembly)
-
Not sure what you are using for a model, but I don't see how one could drill through this BOP. And that is the sole purpose of a BOP, to control a well, but still allow drilling though the shut-off valves and the shears.
Look to me a like a sub sea well head.
Ken
-
@unknownuser said:
Not sure what you are using for a model, but I don't see how one could drill through this BOP. And that is the sole purpose of a BOP, to control a well, but still allow drilling though the shut-off valves and the shears.
Look to me a like a sub sea well head.
Ken
I'll go with that. I haven't been able to get anyone to tell me the difference and only got a vague description form my oilfield friends. I didn't have the picture to show them at the time.
There was also no description of the picture (seriously) when I downloaded it.
Well head? Works for me!
-
I looked at my post, forgot to tell you I liked the model. You have done a good job.
I do a lot of modeling for offshore companies.
You can get rid of the lines, by using the eraser and the control key to hide the lines.
Ken
-
You can go to this web site and watch as an ROV cuts the riser off the BOP.
-
@unknownuser said:
You can go to this web site and watch as an ROV cuts the riser off the BOP.
Man, i hope they get it done...
-
Just call Bruce Willis.........
-
@unknownuser said:
I looked at my post, forgot to tell you I liked the model. You have done a good job.
I do a lot of modeling for offshore companies.
You can get rid of the lines, by using the eraser and the control key to hide the lines.
Ken
Thank you. I will try that tomorrow.
Appreciate the good word.
-
-
@3eighty said:
Just call Bruce Willis.........
Chuck Norris could swim down there and crimp the pipe closed with his teeth.
-
@unknownuser said:
Almost done.
How do I get rid of the lines on top of the gas cylinder? (right hand side of the assembly)
[attachment=0:2dirszvp]<!-- ia0 -->welltreeaux6.jpg<!-- ia0 -->[/attachment:2dirszvp]Insure bell shaped housing is a group, then rightclick, click soften/smooth edges, then
make sure soften normals is checked and adjust slider.p
-
@unknownuser said:
You can get rid of the lines, by using the eraser and the control key to hide the lines.
Ken
Worked like a champ! Thanks.
-
@pmolson said:
@unknownuser said:
Almost done.
How do I get rid of the lines on top of the gas cylinder? (right hand side of the assembly)
[attachment=0:3gj2dy1i]<!-- ia0 -->welltreeaux6.jpg<!-- ia0 -->[/attachment:3gj2dy1i]Insure bell shaped housing is a group, then rightclick, click soften/smooth edges, then
make sure soften normals is checked and adjust slider.p
This worked well also. (I tested both techniques)
Thanks.
-
Done. Thanks to all for the help and suggestions.
-
@unknownuser said:
Done. Thanks to all for the help and suggestions.
[attachment=0:3f10xwfu]<!-- ia0 -->ArguswelltreeFIN.jpg<!-- ia0 -->[/attachment:3f10xwfu]Thats incredible!
-
Thanks NOLA. I wanted to add that I have about 30 hours on this one, which was a huge improvement over my first post here, which took me almost 80 hours.
Still learning.
And loving it.
-
Cool, good job man! Planning on rendering it as well?
-
Really nice modelling, very clean!
PS Happy Birthday
-
You should upload to the Warehouse if you have an account
Advertisement