(Not) Blowout Preventor - Oops
-
Looks good! Can you tell which part has the "fail" stamp on it?
-
-
Almost done.
How do I get rid of the lines on top of the gas cylinder? (right hand side of the assembly)
-
Not sure what you are using for a model, but I don't see how one could drill through this BOP. And that is the sole purpose of a BOP, to control a well, but still allow drilling though the shut-off valves and the shears.
Look to me a like a sub sea well head.
Ken
-
@unknownuser said:
Not sure what you are using for a model, but I don't see how one could drill through this BOP. And that is the sole purpose of a BOP, to control a well, but still allow drilling though the shut-off valves and the shears.
Look to me a like a sub sea well head.
Ken
I'll go with that. I haven't been able to get anyone to tell me the difference and only got a vague description form my oilfield friends. I didn't have the picture to show them at the time.
There was also no description of the picture (seriously) when I downloaded it.
Well head? Works for me!
-
I looked at my post, forgot to tell you I liked the model. You have done a good job.
I do a lot of modeling for offshore companies.
You can get rid of the lines, by using the eraser and the control key to hide the lines.
Ken
-
You can go to this web site and watch as an ROV cuts the riser off the BOP.
-
@unknownuser said:
You can go to this web site and watch as an ROV cuts the riser off the BOP.
Man, i hope they get it done...
-
Just call Bruce Willis.........
-
@unknownuser said:
I looked at my post, forgot to tell you I liked the model. You have done a good job.
I do a lot of modeling for offshore companies.
You can get rid of the lines, by using the eraser and the control key to hide the lines.
Ken
Thank you. I will try that tomorrow.
Appreciate the good word.
-
-
@3eighty said:
Just call Bruce Willis.........
Chuck Norris could swim down there and crimp the pipe closed with his teeth.
-
@unknownuser said:
Almost done.
How do I get rid of the lines on top of the gas cylinder? (right hand side of the assembly)
[attachment=0:2dirszvp]<!-- ia0 -->welltreeaux6.jpg<!-- ia0 -->[/attachment:2dirszvp]Insure bell shaped housing is a group, then rightclick, click soften/smooth edges, then
make sure soften normals is checked and adjust slider.p
-
@unknownuser said:
You can get rid of the lines, by using the eraser and the control key to hide the lines.
Ken
Worked like a champ! Thanks.
-
@pmolson said:
@unknownuser said:
Almost done.
How do I get rid of the lines on top of the gas cylinder? (right hand side of the assembly)
[attachment=0:3gj2dy1i]<!-- ia0 -->welltreeaux6.jpg<!-- ia0 -->[/attachment:3gj2dy1i]Insure bell shaped housing is a group, then rightclick, click soften/smooth edges, then
make sure soften normals is checked and adjust slider.p
This worked well also. (I tested both techniques)
Thanks.
-
Done. Thanks to all for the help and suggestions.
-
@unknownuser said:
Done. Thanks to all for the help and suggestions.
[attachment=0:3f10xwfu]<!-- ia0 -->ArguswelltreeFIN.jpg<!-- ia0 -->[/attachment:3f10xwfu]Thats incredible!
-
Thanks NOLA. I wanted to add that I have about 30 hours on this one, which was a huge improvement over my first post here, which took me almost 80 hours.
Still learning.
And loving it.
-
Cool, good job man! Planning on rendering it as well?
-
Really nice modelling, very clean!
PS Happy Birthday
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login
Advertisement