[Plugin] Component Spray Tool 1.3.

Frederik

This is a GREAT tool...
Would it be possible to make an option, where components sprayed don't intersect with each other...??
It's possible to prevent stacking, but I miss an option, where components don't intersect also...

Perhaps even an option, where I can define how close components can be to each other...
Could have both positive and negative entries...
Any ideas...??

solo

Yes please, I have the same issue where I need to mass some proxies but the boxes I'm using are all stacked and intersecting, maybe a collision checkbox?

csolar

I've just installed this (SU 7.1, WinXP), and I have a question about the spray pressure parameter. In the user guide it says that the # of components dropped is calculated as:

[area of surface]/[average area of component(s)]*[spray pressure]

In my case, the surface is a 10x10 square, and the component is a 1x1 square -- so the surface is 100 times the component area. If I select a spray pressure of 10%, I would expect 10 components to be dropped, but what I get is 100 components. Basically this calculation seems to be off by a factor of 10: if I ask for 100% pressure, then 1000 components get dropped, and so on.

Am I missing something? I ask because for my model I really need lower densities; i.e. in line with the calculation described in the guide.

Thanks,

Chris.

csolar

Another observation:

I select "random rotate", but when I look at the results it's clear that only 6 specific rotation angles are being used...actually more like 3 pairs of angles, 120 degrees apart, with the items in each pair being 8 degrees apart. Is this expected?

Thanks, Chris.

Didier Bur

Hi csolar,
Do you have set any angle snapping ?

Frederik

Hi Didier,

Any chance of adding what Solo and I have requested...??

csolar

@didier bur said:

Do you have set any angle snapping ?

I did, but the results are the same after I turned off angle snapping.

Didier Bur

@unknownuser said:

Any chance of adding what Solo and I have requested...?

Yes. The only question is: when ?

Frederik

@didier bur said:

Yes.

@didier bur said:

The only question is: when ?

Hopefully soon...

thomthom

Didier:

If you replace the native model.raytest with this method the rays won't stop on invisible entities:


  # Raytrace method that does not stop on hidden entities.
  def self.raytest(ray)
    model = Sketchup.active_model
    vector = ray[1]
    while true
      # Shot ray
      test = model.raytest(ray)
      return nil if test.nil?
      # Verify visibility
      point, path = test
      if path.all? { |e| e.visible? && e.layer.visible? }
        return test
      else
        # raytest stopped on a hidden entity - create a new ray from that point
        # and let the loop continue until it hits something visible, or nothing.
        ray = [ point, vector ]
      end
    end # while
  end

Didier Bur

Hi tt,

inbal

thank so much

lapx

Problems with component spray tool...Tool will not pick point after clicking.
Is anyone else have problems with the tool? All the parameters appear correct.
I'm placing byce on a simple plane is not working. Openig a new drawing helped but it always goes back to not working at some point.

I'm using in V6.

charly2008

Hi,

I wanted to try compo spray but I get a huge number of components at a small circle. What am I doing wrong?

Charly

Didier Bur

Hi,
Did you draw a great circle (20m or so) or a small one (2m or so) ?
But don't worry, since FaceMe components don't really have a bounding box, the number of components to be created is wrong, if I remember well...
Regards,

charly2008

Hi Didier,

The circle was about three meters. I tried the whole day. If i use it at a single line or a point then i get very small copies.

Charly

Untitled.skp

charly2008

For the above mentioned problem i found the solution. The values for Low and high scale where to less.

But now although Keep vertical is selected, the tree is horizontal. For this I could not find the reason.

Charly

charly2008

Hi,

I found the error. This component was the reason. After I exploded the component and made it a new component, the error was gone.

Charly

mariocha

I'm having difficulty to make it work in SU 8.
Confirmation ?
But it is my first try, I must say.

thomthom

@mariocha said:

I'm having difficulty to make it work in SU 8.
Confirmation ?
But it is my first try, I must say.

Exactly what isn't working?