sketchucation logo sketchucation
    • Login
    πŸ›£οΈ Road Profile Builder | Generate roads, curbs and pavements easily Download

    Stanley 4 1/2 Plane

    Scheduled Pinned Locked Moved WIP
    27 Posts 7 Posters 9.2k Views 7 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • tuna1957T Offline
      tuna1957
      last edited by

      Well got the body casting finished….. I think. Ohh…. did I mention the plane has a corrugated sole ? 😎


      stanley 4 1-2 plane body.jpg

      1 Reply Last reply Reply Quote 0
      • tuna1957T Offline
        tuna1957
        last edited by

        Thanks Bryan, Thanks Mike. Everyone should hold off on the β€œgreat” comments until I get this thing finished ! Might get frustrated and throw it in the trash πŸ˜† . Just doing it for a little change of pace. It will patiently wait in the parts bin. Might get used at some point or it might just take up a little drive space collecting dust. πŸ˜‰

        1 Reply Last reply Reply Quote 0
        • tuna1957T Offline
          tuna1957
          last edited by

          Handle and knob in place...... now for the the frog ..... yippee !!!!! 😞


          stanley 4 1-2 plane.jpg

          1 Reply Last reply Reply Quote 0
          • Mike AmosM Offline
            Mike Amos
            last edited by

            πŸ‘

            1 Reply Last reply Reply Quote 0
            • Bryan KB Offline
              Bryan K
              last edited by

              Excellent. πŸ‘

              See my portfolio at https://delphiscousin.blogspot.com/

              1 Reply Last reply Reply Quote 0
              • alvisA Offline
                alvis
                last edited by

                Nice πŸ‘

                1 Reply Last reply Reply Quote 0
                • tuna1957T Offline
                  tuna1957
                  last edited by

                  Thanks gentlemen 😎

                  1 Reply Last reply Reply Quote 0
                  • tuna1957T Offline
                    tuna1957
                    last edited by

                    The frog is done ! Hooray ! Down to the small bits and threading the machine screws πŸ˜• 😎


                    frog.jpg

                    1 Reply Last reply Reply Quote 0
                    • tuna1957T Offline
                      tuna1957
                      last edited by

                      Oops….. forgot the knurling on the adjustment knob….. me bad….. here it is ! πŸ˜‰


                      knurling.jpg

                      1 Reply Last reply Reply Quote 0
                      • tuna1957T Offline
                        tuna1957
                        last edited by

                        Got the hold-down screw for the lever cap done. In the process noticed I forgot a couple of casting recesses in the bottom side of the frog ! I suspect there is going to be a lot of going back for things I missed. πŸ˜†


                        frog3.jpg

                        1 Reply Last reply Reply Quote 0
                        • pbacotP Offline
                          pbacot
                          last edited by

                          OK. Someone had to say it. Can we see the hidden geometry? Hungry for more!

                          MacOSX MojaveSketchUp Pro v19 Twilight v2 Thea v3 PowerCADD

                          1 Reply Last reply Reply Quote 0
                          • tuna1957T Offline
                            tuna1957
                            last edited by

                            pbacot , you asked for it...... might wear you out with this mess ! πŸ˜†


                            plane HL.jpg


                            planeHL2.jpg


                            planeHL3.jpg

                            1 Reply Last reply Reply Quote 0
                            • Dave RD Offline
                              Dave R
                              last edited by

                              Excellent! Very sharp model. You've really been honing your skills.

                              Etaoin Shrdlu

                              %

                              (THERE'S NO PLACE LIKE)

                              G28 X0.0 Y0.0 Z0.0

                              M30

                              %

                              1 Reply Last reply Reply Quote 0
                              • tuna1957T Offline
                                tuna1957
                                last edited by

                                Thanks Dave. Hardest part has been getting the measurements off the original ! 😎

                                1 Reply Last reply Reply Quote 0
                                • Dave RD Offline
                                  Dave R
                                  last edited by

                                  I magine that is a challenge. Especially with castings.

                                  Etaoin Shrdlu

                                  %

                                  (THERE'S NO PLACE LIKE)

                                  G28 X0.0 Y0.0 Z0.0

                                  M30

                                  %

                                  1 Reply Last reply Reply Quote 0
                                  • tuna1957T Offline
                                    tuna1957
                                    last edited by

                                    Dave , should have also mentioned I had to watch your β€œscrew thread β€œ tutorial about eight times before I could make a reasonable looking machine screw πŸ˜† .

                                    1 Reply Last reply Reply Quote 0
                                    • Dave RD Offline
                                      Dave R
                                      last edited by

                                      So I must have missed some detail?

                                      Nice threads, by the way.

                                      Etaoin Shrdlu

                                      %

                                      (THERE'S NO PLACE LIKE)

                                      G28 X0.0 Y0.0 Z0.0

                                      M30

                                      %

                                      1 Reply Last reply Reply Quote 0
                                      • tuna1957T Offline
                                        tuna1957
                                        last edited by

                                        @dave r said:

                                        So I must have missed some detail?

                                        No you missed nothing. I’m just a little slow at times πŸ˜†

                                        1 Reply Last reply Reply Quote 0
                                        • Dave RD Offline
                                          Dave R
                                          last edited by

                                          Ahh.... Well, that's not all bad. πŸ˜‰

                                          Etaoin Shrdlu

                                          %

                                          (THERE'S NO PLACE LIKE)

                                          G28 X0.0 Y0.0 Z0.0

                                          M30

                                          %

                                          1 Reply Last reply Reply Quote 0
                                          • tuna1957T Offline
                                            tuna1957
                                            last edited by

                                            On the downhill side of this. All parts are modeled ( I think πŸ˜† ) . Beveling edges now... Here's an image to make your eyes cross... X RAY ! 😎


                                            x ray.jpg

                                            1 Reply Last reply Reply Quote 0
                                            • 1
                                            • 2
                                            • 1 / 2
                                            • First post
                                              Last post
                                            Buy SketchPlus
                                            Buy SUbD
                                            Buy WrapR
                                            Buy eBook
                                            Buy Modelur
                                            Buy Vertex Tools
                                            Buy SketchCuisine
                                            Buy FormFonts

                                            Advertisement