Problems with a half-torus
-
Thanks again d12dozr, that is a real help. I thought I had to put in all those supports and had been scrabbling around the t'interweb trying to find where and what spacing you put them in at.
Back to the drawing board for v14 it is then....
-
I am getting the hang of it! V19 was drawn in 45 minutes last night, solid first time
-
Cool but you have forgotten the V6!
-
-
New design is SEXY!
One question...is this area under much stress? If so it may be a good idea to add some meat so it doesn't break easily.
-
Not much stress, it only has to hold the weight of itself up and the one my mate test-printed weighed in at 50g so not very much at all, nothing that a suitable washer won't support (I hope
). This version will weigh in a fair bit lighter too. -
Well since you pointed that out I've had the compulsion to fiddle
But... I can't work out a way to add a bit of 'meat' to that area? Short of starting from scratch that is. To strengthen that area I've tried making an arc on the base and Push/Pulling but it leaves gaps.v6 added for Pilou
-
I would try making the shape you want to add as a separate solid group, then use Outer Shell to combine them.
-
More study required...
-
I'm back again
I'm on version 34 (or so) now. After a lot of research reading mind-boggling papers on how to optimise the design I have changed my design slightly.I'm having problems with the Follow Me tool again, it won't do this:
Is there any way I can make it work? I've tried it a few ways on different radius circles to follow, but it will not have it. I've tried it with half-circles and solid circles, this version is trying to be hollow to save weight. Anyone have any ideas?
v6 for Pilou
:
-
Moved the face away from the other geometry and scaled the model up (1000x)...
-
@unknownuser said:
v6 for Pilou
Not just for me but for all users who have not the same up version than you!
PS you are making an engine in 3D Printing ?
What will be the fuel ? And for what vehicle ? -
@cotty said:
Moved the face away from the other geometry and scaled the model up (1000x)...
[attachment=0:1vs06ddx]<!-- ia0 -->follow34.jpg<!-- ia0 -->[/attachment:1vs06ddx]
That looks brilliant.
Err.. How do I move a face away from the other geometry? Every time I try I get little 'strings' attached that just stretch out.
And the scale tool. Sorry for sounding stupid but if I scale it by a 1000x what do I sale by to get back to my dimensions?
Thanks.
-
@pilou said:
@unknownuser said:
v6 for Pilou
Not just for me but for all users who have not the same up version than you!
PS you are making an engine in 3D Printing ?
What will be the fuel ? And for what vehicle ?Yes, it's to go on the carburettor intake on a petrol powered 1976 Austin Mini, my daily drive.
-
Carsten (cotty) did it exactly how I would have
@teig said:
And the scale tool. Sorry for sounding stupid but if I scale it by a 1000x what do I sale by to get back to my dimensions?
.001
You can also use the Tape Measure tool to quickly and accurately scale a model.
It's neat to watch your design iterations gradually improve
-
@d12dozr said:
Carsten (cotty) did it exactly how I would have
@teig said:
And the scale tool. Sorry for sounding stupid but if I scale it by a 1000x what do I sale by to get back to my dimensions?
.0001
If you look at p. 36 of my book, I explain how to use the Tape Measure tool and a reference line to quickly and accurately scale a model.
It's neat to watch your design iterations gradually improve
Thanks a lot Marcus, I knew it had to be some amount of 000s
It is one mighty learning curve, I'm sure a hotel would be an easier way to get started I'll go look at your book now, I haven't had much time to myself recently.
-
Hey Teig, I messed up the first time around...it should be .001. Sorry, I edited my post, but you already caught it.
Also the way to move the geometry is to draw a line separating the piece you want to follow-me, then group it for moving (or copy it and erase the original).
-
And while you are at it, you can make the piece a component, then scale a copy up to do your edits, then delete the large copy and the edits will have worked on the small version.
-
@d12dozr said:
Hey Teig, I messed up the first time around...it should be .001. Sorry, I edited my post, but you already caught it.
Also the way to move the geometry is to draw a line separating the piece you want to follow-me, then group it for moving (or copy it and erase the original).
Ah, OK, I wondered about your zeros but bowed to your wisdom
I've scaled it all up, I couldn't figure out how to separate the two parts so ran the Follow Me, it worked But... it wasn't solid so I ran SolidSolver which is really struggling at present and has been stuck on the Spinning Beachball of Doom for 10 minutes. Here's hoping... -
@box said:
And while you are at it, you can make the piece a component, then scale a copy up to do your edits, then delete the large copy and the edits will have worked on the small version.
Oh yeah??? That sounds like a great system! Let me get this correct... So the times when Follow Me won't work on my tiny component will work on the scaled up? And affect the edits on the tiny copy? Wow!
Advertisement