Please help... :S ( British Museum roof structure )

bjornkn

Nice again
I just found a top view of it, from a WIP that claims that it was drawn from a plan in a book.
http://forums.cgarchitect.com/36383-british-museum-great-court.html

The even, swirly vertical ribs would be quite difficult to make without a lot of hand editing, don't you think?

Alan Fraser

@bjornkn said:

The even, swirly vertical ribs would be quite difficult to make without a lot of hand editing, don't you think?

Absolutely. I don't think it's possible to take shortcuts with this. I found that it's even important which diagonal you draw first when triangulating the 'squares'. If you do the wrong one, then those swirly ribs get distorted.
This needs a little more refinement, but here is the basic methodology:

Lay out a groundplan.

Intersected and stretched a little more rectangular.

You only need 1/4

Pull every other segment upwards.

Delete the joining lines to leave the vertical planes.

Construct curves on each face...equal segments, equal height.

Skin and triangulate...a full X in each square section, not just the single necessary diagonal

Flip all of the horizontals to create intermediate radial ribs.

Mirror copy to complete.

pbacot

This is from the 80 megapixel panorama of London

BM roof.png

bjornkn

Here is my go at it. I love a challenge, and hate to give up
It was lots of work, and quite a lot of hand editing.
Without Amorph Bezier curves and view locking I don't think I would have tried.
It could still need some tweaking, and I just noticed that the rotunda is not in the middle of the room on the plan !
Used TIG's LatticeMaker to make the frames/glass - it took almost 2 hours in all!

rpaul

Alan, I'm trying to follow your methodology and got lost at the "skin and triangulate" and "flip all the horizontals". What steps did you take to "skin and triangulate"? Did you use the skin.rb and sds? The second question is what do you mean by "flip all the horizontals"? I see the horizontals are gone but how are they flipped to accomplish what I'm seeing. Thanks for any insight.

joypsj

OMG!!!! You guys are GENIUS!!!!! I didn't read all yet but there is the answer for sure! Thank you sooooo mush!

Alan Fraser

I have to warn you that my model is not entirely accurate, as the actual roof does not have straight radial ribs, they are slightly curved; nor does it have obvious diagonals at the corners...nor is it the same height along the narrow sides that it is along the broader ones...nor is the central, circular reading room exactly in the middle (as Bjorn points out). There are also about 50% more segments going outwards on the broader side than on the narrow one...and about 100% more on the diagonal. Otherwise it's fine.

I found a clearer layout of the rib structure. Apparently the first drafts were mathematically procedural...rather like mine, but left awkward shapes around the exterior. The final result was arrived at after much experimentation and represents a compromise between visual appeal and stress considerations. (The whole of the circular edge is on 'castors' to avoid any lateral strain on the Reading Room. The accuracy is phenomenal. It's over 90m long yet is accurate to +/- 3mm.

I used the Curviloft skinning tool, but to be honest, it wouldn't have taken much longer not to...because many of the produced diagonals were the 'wrong' ones. I also forgot to mention (but it's fairly obvious) that I first deleted the base lines of all the arcs...so that you're left with just a framework of edges to deal with.
I think I mentioned somewhere that it was important to decide which diagonal went in first. By diagonals I mean those that fill-in the roughly square shapes defined by the horizontal lines.. Because these shapes aren't planar, you can't simply draw two diagonals. You have to draw one, then draw the second one from the corner to the mid point of the first diagonal...then to the other corner. If this second diagonal is something of a dog leg, then erase and do it all the other way around.

By flipping, I simply mean use the Flip tool in the Sandbox to turn all the horizontals into radials.
I hope you can follow this.

Bjorn, really great job. I had another go myself after I found more accurate reference. This is definitely something that can't be automated....although I have seen an animated demo done in Rhino. I think it may be on YouTube.

pilou

[flash=425,349:kwxv0ccf]http://www.youtube.com/v/-AGQajhDegM?version=3[/flash:kwxv0ccf]

bjornkn

Nice video
Any idea why YouTube videos can't be viewed at full screen on this forum?

Thanks to Alans new and better plan I had to waste some more time on this

Here's a short tut of the first steps of making it with Amorph.

Gaieus

@bjornkn said:

Any idea why YouTube videos can't be viewed at full screen on this forum?

The way YT videos are embedded nowadays have changed and the forum software only allows the old embed code which is now limited.

bjornkn

Here's a little update on the roof, with a few curves finalized and filled in with Bezier meshes. It is actually a lot faster doing it than describing how it's done..

irwanwr

too advanced for me