sketchucation logo sketchucation
    • Login
    ℹ️ Licensed Extensions | FredoBatch, ElevationProfile, FredoSketch, LayOps, MatSim and Pic2Shape will require license from Sept 1st More Info

    Problems with modeling from Acad drawings

    Scheduled Pinned Locked Moved SketchUp Discussions
    sketchup
    33 Posts 21 Posters 2.6k Views 21 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • H Offline
      Howard leslie
      last edited by

      We use Autocad / SketchUp all the time and are back and forth between the 2 programs constantly.
      If we produce the CAD drawings - no problem 99 % of the time.

      Occasional problems occur when curves turn into straight lines - sometimes you get clashes where previously in the CAD data you didn't. If you're aware of this SketchUp limitation you can get around it most of the time.
      .........
      If another Company has produced the CAD drawings then sometimes we have problems.
      In other words, the problem you are experiencing is most likely not an Autocad problem.

      If your CAD operators are using AutoCad as opposed to another CAD package and exporting as dwg / dxf out then the problems are most likely to be CAD operator error ie sloppy drawing.
      Zoom in to some of the linework junctions / intersections in Autocad - are the joins good ???
      ........
      Some CAD packages that export dwg / dxf (ie none Autocad) can mess the data up.
      We've been on the receiving end of some of this junk also - can be a real nightmare.
      ........
      Make sure your CAD operators are using the Snaps correctly in Autocad - End Point, Mid Point, Perpendicular etc.
      All linework should be crisply snapped together - no over / under shoots.
      Get them to turn off Nearest Snap - or use with caution - can be lethal in the wrong hands !!!
      .........
      Data Clean Up (in Autocad)

      1. Turn drawing edge on - you should see a long flat line / lines. Anything above or below (0) is floating or drilled into the ground and needs fixing. (Manual Fix or FLATTEN)

      2. FLATTEN Command - makes everything 2d

      3. OVERKILL Command - eliminates duplicates

      4. PURGEALL Command - Cleans out unused Blocks / Layers etc
        .........
        Hope this Helps

      Howard L'

      1 Reply Last reply Reply Quote 0
      • mitcorbM Offline
        mitcorb
        last edited by

        In Autocad, if you click on a vector you should see blue "grips". Right click on one of the grips select properties in the fly out menu. A tab should appear at the edge of the screen with a scroll window. Find the Z start, Z end. Edit the data in each of these fields. That's for one at a time. There is also a way to look globally at properties for all items whether polylines or vectors or arcs or whatever and look at these properties to find z values which can be corrected. Smart Blocks would have to be dumbed down by exploding, sometimes twice, before squashing to zero but you will lose 3d data you may have relied upon.

        The only running snap I keep on is Intersection. You can Shift+right click to bring up snap context menu where you can change momentarily to any available snap. One I like a lot is Mid between 2 Points. This can be used for the "from point" and the "to point" for copying, mirroring, moving, and rotating and so on.

        I take the slow, deliberate approach in my aimless wandering.

        1 Reply Last reply Reply Quote 0
        • C Offline
          cobb89
          last edited by

          @honoluludesktop said:

          One of the biggest problems is with attempting to place a surface on existing coplaner line ends, if there was a slightly overlapping line intersecting the face I was attempting to create, SketchUp refused to insert the face until I corrected the Acad drawing. Can anyone tell me if it matters that I import dxf or dwg files?

          can you post a screenshot here

          @honoluludesktop said:

          Other problems I faced, was the weld.rb would frequently cause SketchUp to splat. Is that common?

          I've never had that problem. I'd suggest you one useful plugin Makefaces ..it's available for free on smustard. You should surely give it a try. It's really useful plugin. I work with cad files a lot on sketchup and find this plugin really handy.

          1 Reply Last reply Reply Quote 0
          • honoluludesktopH Offline
            honoluludesktop
            last edited by

            First is imported dwg
            Temp00.pngThen is attempt to surface steps. Note the lowest thread failed to surface.
            Temp01.pngThen, clean up of extra lines.
            Temp02.pngThen, good surface.
            Temp03.pngDetailed example of crossing line fragment. Temp04.pngBecause you asked, I looked more closely at the problem. The line fragment is very small, maybe the problem has to do with SketchUps defaults as to selecting inferencing points.

            1 Reply Last reply Reply Quote 0
            • thomthomT Offline
              thomthom
              last edited by

              @honoluludesktop said:

              closely at the problem. The line fragment is very small, maybe the problem has to do with SketchUps defaults as to selecting inferencing points.

              Try my Edge Tools 2 plugin, I got a tool there that highlights open ends and tries to close them, or remove tiny edge fragments.

              Thomas Thomassen — SketchUp Monkey & Coding addict
              List of my plugins and link to the CookieWare fund

              1 Reply Last reply Reply Quote 0
              • mitcorbM Offline
                mitcorb
                last edited by

                I will vouch for thomthom's Edge Tools. Very effective. Salute to you, Thomas!

                I take the slow, deliberate approach in my aimless wandering.

                1 Reply Last reply Reply Quote 0
                • honoluludesktopH Offline
                  honoluludesktop
                  last edited by

                  Thanks for the heads up, sounds like it will be a big help.

                  1 Reply Last reply Reply Quote 0
                  • G Offline
                    Glenn at home
                    last edited by

                    +1 on this one. This is the way I always do it.

                    @yahellid said:

                    In general, I try to never use the actual lines from the CAD file as lines for my sketchup model. It's almost always a matter of putting it on a locked layer and tracing over it. That way I know that what I'm doing is clean and organized as I need it.

                    SketchUp Pro 2024/2025 Dell XPS 8950 i9-12900K 64GB Ram RTX 3080

                    1 Reply Last reply Reply Quote 0
                    • honoluludesktopH Offline
                      honoluludesktop
                      last edited by

                      What's a locked layer?

                      1 Reply Last reply Reply Quote 0
                      • D Offline
                        designerstuart
                        last edited by

                        @honoluludesktop said:

                        What's a locked layer?

                        you can hide a layer - maybe they mean this? i just group it though.

                        also i thought there was a plugin somewhere maybe called StrayLines that was a big help for this. MakeFaces is good for dwg imports too.

                        1 Reply Last reply Reply Quote 0
                        • AnssiA Offline
                          Anssi
                          last edited by

                          An old trick I use is to never use the imported linework except for inferencing. I place the imported drawing some way up from my "work plane". Then I draw a large rectangular face. Then I start modelling with the rectangle or line tool, placing it on the face until the "on face" tooltip appears, press down Shift, and start clicking away at the points in the imported 2D component. I also try to keep an eye on axiality to avoid the ******* small deviations that try to creep in (yes, there are sloppy drafters in my colleagues, and I am sometimes one too).

                          Anssi

                          securi adversus homines, securi adversus deos rem difficillimam adsecuti sunt, ut illis ne voto quidem opus esset

                          1 Reply Last reply Reply Quote 0
                          • honoluludesktopH Offline
                            honoluludesktop
                            last edited by

                            Good ideas, all. Am trying out some at this time. Thanks.

                            1 Reply Last reply Reply Quote 0
                            • G Offline
                              Glenn at home
                              last edited by

                              @honoluludesktop said:

                              What's a locked layer?

                              The layer is visible but locked. You cannot edit it's contents in any way.

                              SketchUp Pro 2024/2025 Dell XPS 8950 i9-12900K 64GB Ram RTX 3080

                              1 Reply Last reply Reply Quote 0
                              • D Offline
                                Drafter X
                                last edited by

                                I can tell your working with architectural drawings. I'm going to say what most will not, and that is that architects are some of the absolute worst when it comes to drawing things precisely in autocad drawings. Snap to grid, ortho on and precision set to whole inches and over ridden dimensions everywhere are just a few of the issues we have seen in the majority of architectural cad files I have had the displeasure of dealing with. Why? I don't have any idea, but it is unfortunately more often the rule instead of the exception, and I would get fired for drawing things that way.

                                I apologize to those architects that don't do this, if you don't, be happy that you are the exception.

                                If you are one of those people that do this, don't bother making a defense for it, I really don't mind, we make a huge amount of money creating shop drawings and putting in change orders when the things specified are a physical impossibility and we get to charge to make it work. 😆

                                1 Reply Last reply Reply Quote 0
                                • TIGT Offline
                                  TIG Moderator
                                  last edited by

                                  I think in the context 'locked instance' was meant rather than 'locked layer' - you can't lock a layer in SKP [you can in CAD] BUT you can 'lock' a SKP's groups and instances so that they can't be moves, deleted or changed until you 'unlock' them...

                                  On the topic of rubbish CAD drawings... I once had the unenviable task of doing the construction drawings and documents for a maximum security prison originally designed by one of the governments most respected consultants and signed off on a set of design drawings and a scaled wooden model. We got the CAD drawings [plans, sections and elevations] and set about working up the scheme. I realized that you couldn't form the complex hipped roof as they had shown on the roof plan and elevations - there were two eaves heights between two main block 'wings' with a connecting 'arm' - there are rules about prison roofs having no flat or hidden areas, slopes, non-grapple-ability etc... I was exasperated! After a lot of brain ache I came up with a solution that worked to everyones satisfaction... We had never seem the physical model because it was on someones desk at the Home Office. When I discreetly raised the balls up with one of their architects she said, 'Oh yeah, we knew the roof didn't work when we came to make the physical model and had to fudge it - we didn't have time to change the drawings...' [they also didn't have the courtesy to tell us either] 😒 IF they had made a simple SKP model it would have showed them at an early stage that the 2D CAD just didn't work - it is possible to check that your 2D CAD DWGs all align and work in unison BUT too difficult for many to bother to do 😒 😒

                                  TIG

                                  1 Reply Last reply Reply Quote 0
                                  • E Offline
                                    edgeman4
                                    last edited by

                                    I was just looking at this issue on importing AutoCAD to Sketchup and I wanted to find places where there was discontinuity in connecting lines. Well it turns out it looks like sketchup really has a problem with AutoCAD curves, and this seems to be where most of my problems arise. I saw that where straight lines meet a curved arc, the lines almost rarely meet. However I went back and looked at the ACAD file and the line is definitely hitting the curve. I know Sketchup has never been very good with curves so this must be one of the main issues with importing, besides bringing in imprecise ACAD drawings.

                                    1 Reply Last reply Reply Quote 0
                                    • TIGT Offline
                                      TIG Moderator
                                      last edited by

                                      Assuming the curves are arcs/circles and not part of 3d faces then there's my tool to increase the number of segments from the default 24s etc, this will reduce the gap... and if you are lucky it might even even close it, if a node is coincident with a line's end.
                                      Thomthom have some great tool to tidy-up / enhance CAD drawing [Edge Tools, Plan Tools etc] - useful for closing small gaps, sloppy drafting errors, simplifying etc, which will be useful to you.
                                      Use the 'Plugins Index' red button and then a browser-search for us as authors... and/or by keyword like 'segment' or 'edge' or 'plan'... follow the download pages' instructions - I know that some of tt's tools need a second download of helpers = usually TT_Lib2 linked from his page...

                                      TIG

                                      1 Reply Last reply Reply Quote 0
                                      • J Offline
                                        jpalm32
                                        last edited by

                                        @tig said:

                                        I think in the context 'locked instance' was meant rather than 'locked layer' - you can't lock a layer in SKP [you can in CAD] BUT you can 'lock' a SKP's groups and instances so that they can't be moves, deleted or changed until you 'unlock' them...

                                        Funny! I have done many security layouts for jails and the one architect never doing a jail before, had skylights over the cells. Real glass, no bars, skylights.
                                        He cut pasted from a motel project.
                                        Cut & Paste is a problem no one mentioned. I see many "Boiler plate cut-outs" drawing not even related to the project on drawings.

                                        1 Reply Last reply Reply Quote 0
                                        • GISdudeG Offline
                                          GISdude
                                          last edited by

                                          @drafter x said:

                                          I can tell your working with architectural drawings. I'm going to say what most will not, and that is that architects are some of the absolute worst when it comes to drawing things precisely in autocad drawings. 😆

                                          I beg to differ - engineers are the absolute worst at snaps, trims, etc. Not to mention there redlines on drawings...

                                          1 Reply Last reply Reply Quote 0
                                          • GISdudeG Offline
                                            GISdude
                                            last edited by

                                            This is a very good post.

                                            I come from the GIS (Geographic Info Systems) world. What we typically do when creating maps is construct a "topology". This is "cleaning up" your map. So, snap nodes, trim lines, snap line, remove duplicates. Very time consuming, but there is a decent work flow to getting your topology to work. You can run the various python scripts to find errors and then zero in on them and correct it. I believe in the 3D world some people will typically say the "geometry must be manifold", which to me is synonymous with "creating a topology".

                                            My 2 cents,

                                            1 Reply Last reply Reply Quote 0
                                            • 1
                                            • 2
                                            • 2 / 2
                                            • First post
                                              Last post
                                            Buy SketchPlus
                                            Buy SUbD
                                            Buy WrapR
                                            Buy eBook
                                            Buy Modelur
                                            Buy Vertex Tools
                                            Buy SketchCuisine
                                            Buy FormFonts

                                            Advertisement