Need help punching pattern into cylindrical object
-
@maclee said:
I was just about ready to give up...
Lee
Please don't... Stick around until the point you will be able to help others as others helped you.
The cycle must not stop
-
@jql said:
@maclee said:
I was just about ready to give up...
Lee
Please don't... Stick around until the point you will be able to help others as others helped you.
The cycle must not stop
haha, right! I have a feeling I will be posting quite often... Sketchup is such a fun program to learn and even more so when you have people helping you when you get stuck!
-
@jql said:
The pattern isn't right but it was a 15 minute doodle.
Using a single plugin: shape bender...
JQL, how did you go from the step on the right to the one on the left?
Also, your final shape has quite a bit of overlap. I assume this is not ideal for a 3d print. Curious.
-
I used shape bender using the arc of rhe pie.
In the end there's cleaning up to do to reach the last step as shape bender wasn't able to compress the bottom center part to an edge.
-
Cheers. -
@jql said:
I used shape bender using the arc of rhe pie.
I have used Shape Bender many times but not sure I fully get this part. Fully comprehend doing the curve to obtain the shape of the vessel but do not fully comprehend how to perform the taper.
-
@jql said:
I used shape bender using the arc of rhe pie.
In the end there's cleaning up to do to reach the last step as shape bender wasn't able to compress the bottom center part to an edge.
When I bend my shape many of my petal cutouts get messed up, do you think it could be because I am working in real scale and I should start larger and then shrink it down? Yours stayed so perfect!
My real scale is bottom c=22cm top c=64cm height 24cm
-
@maclee said:
When I bend my shape many of my petal cutouts get messed up, do you think it could be because I am working in real scale and I should start larger and then shrink it down? Yours stayed so perfect!
My real scale is bottom c=22cm top c=64cm height 24cm
That should be the issue. Try scaling it up by 10 and then 10 again until Shape Bender doesn't cause issues.
-
@ntxdave said:
@jql said:
I used shape bender using the arc of rhe pie.
I have used Shape Bender many times but not sure I fully get this part. Fully comprehend doing the curve to obtain the shape of the vessel but do not fully comprehend how to perform the taper.
The trick with shape bender is that the edge that is parallel with the component, must be in the vertical projection of the component's X axis. Then you can control the final result precisely like this (click the gif):
-
Using a single plugin: shape bender...[/quote]
JQL, how did you go from the step on the right to the one on the left?
[attachment=1:3hjnzs8x]<!-- ia1 -->Capture.JPG<!-- ia1 -->[/attachment:3hjnzs8x]It looks like perhaps he scaled it to match the size of the triangle?
-
Check the following gif.
-
@jql said:
Check the following gif.
I was just struggling with that part. Great how you used the bend tool again to create that triangular shape at the end. Lets see if I can pull it off now... lol
-
@jql said:
Check the following gif.
This is great JQL however when you have to trim the edges because of the overlap the original pattern is destroyed. I have been struggling with the right angle to make the shape "wedge" to a point so no trimming is necessary.
-
@boofredlay said:
@jql said:
Check the following gif.
This is great JQL however when you have to trim the edges because of the overlap the original pattern is destroyed. I have been struggling with the right angle to make the shape "wedge" to a point so no trimming is necessary.
What if you trim the shape at the beginning with the original strip. Starting the trim at the same spot the shape starts to bend and then ending it at the width for the bottom circle ratio. It would possibly give a bit more control over the scaling of the pattern but the angle would only work if it was a uniform arc. Is this right?
-
@boofredlay said:
@jql said:
Check the following gif.
This is great JQL however when you have to trim the edges because of the overlap the original pattern is destroyed. I have been struggling with the right angle to make the shape "wedge" to a point so no trimming is necessary.
Share your model at the same stage boofredlay, I'm sure there is a solution.
-
Well I am making progress but still issues that seem a bit too complicated for me to figure out. Maybe I need a more simple pattern.
Link to file: https://www.dropbox.com/s/zovsd033cyixims/pattern_v4.skp?dl=0
-
sorry I deleted this post and updated it below.
-
@jql said:
@boofredlay said:
@jql said:
Check the following gif.
This is great JQL however when you have to trim the edges because of the overlap the original pattern is destroyed. I have been struggling with the right angle to make the shape "wedge" to a point so no trimming is necessary.
Share your model at the same stage boofredlay, I'm sure there is a solution.
Here you go but as you can see, the edges will never taper properly to a point. The repeating pattern is destroyed each time. I think the method I used originally works much better, slower but more accurate.
-
@maclee said:
Well I am making progress but still issues that seem a bit too complicated for me to figure out. Maybe I need a more simple pattern.
I'd say you need a simpler section of that pattern. What you could do is probably make a section of half the pattern and then mirror it, create a section component and polar array it with the rotate tool.
-
@boofredlay said:
Here you go but as you can see, the edges will never taper properly to a point. The repeating pattern is destroyed each time. I think the method I used originally works much better, slower but more accurate.
I'm sure you're right, but I'll give it a shot anyway.
Advertisement