Animator and Ambient Occlusion

ntxdave

@ntxdave said:

Have one running now that still has another 2+ hours to go.

Precisely.

In animator, click on Preview Video

then Click on the second icon of the AO toolbar (render in a separate winodw), and go to the 7th icon in the top icon bar to select quality to Low.

Then back in Animator, click on Resume Generation.

Fredo

Has not adjusted the time yet but the frames do seem to be rendering faster. I will post it in this thread when it finishes

It finished much quicker.....I posted it in the Gallery thread. While this drone demo looks much better than the original one, I still have some reservations for my car wash models because of the shadows.

Thanks for the tip Fredo..........

fluid

In AmbientOcclusion, the Shadow control is independent from SketchUp. There are two ways you can turn off shadows:

Go to AmbientOcclusion Ex -> Render Viewport, right-click on the viewport -> Shadows -> Enabled
Go to AmbientOcclusion Ex -> Render Window, click on the Shadows icon -> Enabled

ntxdave

@fluid said:

In AmbientOcclusion, the Shadow control is independent from SketchUp. There are two ways you can turn off shadows:

Go to AmbientOcclusion Ex -> Render Viewport, right-click on the viewport -> Shadows -> Enabled

Go to AmbientOcclusion Ex -> Render Window, click on the Shadows icon -> Enabled

Thanks, that worked. I will have another render a little later today.

ntxdave

Here is still another version of my partial car wash.

I added a little more equipment and changed the color or the brushes.

For me, here are the problems I see (and I hope someone can tell my how to address them):

While some edges are removed which is nice, the doors and some detail on the car are missing.
I do not see how to control the lighting. It is kind of dark to me. If I had a ceiling or roof, everything would probably be even darker.
I used the Low quality so it is a little grainer than I would like but this one still took over an hour. If I tried to do a full car wash or I bumped up the quality it could take all day. I am a little more concerned about the quality than the time so I have to make a decision about time versus quality.

In general, It is very easy to produce the rendered video using AmbientOcclusionEx and Animator. Will continue trying some more things before my trial period expires. I think this type of coordination between the two tools is a good step in the right direction though. Kind of wish I could try the Thea or that I could use Twilight in conjunction with Animator.

fluid

If the scene is too dark, go to AmbientOcclusion and try setting the "Occlusion Distance" parameter to a value of 1 or 2, and try to increase the "Gain" parameter a bit.
Also, to increase the rendering speed, you can go to the Render Window of AmbientOcclusion and set a lower resolution. Normally you don't need to render animations at the same resolution as still images.

ntxdave

@fluid said:

If the scene is too dark, go to AmbientOcclusion and try setting the "Occlusion Distance" parameter to a value of 1 or 2, and try to increase the "Gain" parameter a bit.
Also, to increase the rendering speed, you can go to the Render Window of AmbientOcclusion and set a lower resolution. Normally you don't need to render animations at the same resolution as still images.

Thanks, I gave these a try. In the previous video (and this one), I did have the render set to "low" resolution. I tried messing with the "Occlusion Distance" and "Gain" settings. Here is the result:

Can you give me a little insight into what these 2 settings are really all about? And also, would SketchFX add anything?

Now here is one last video in this set where I extended the length of the car was just a little, added an "animated water spray", and set it up as 2 scenes so that the spray does not show up until it is called for. This was achieved by setting up 2 scenes and then adding "views" that show the 2 different scenes during the animation.

In this video, the animation of the spray does not show up very well.

fluid

The "Gain" parameter changes the overall brightness of the image.

The "Occlusion Distance" parameter changes the maximum distance for object to be considered while generating the soft shadows from the environment. For example, let's say you are rendering an interior. By setting the occlusion distance to 1 (1 meter) the ceiling for example won't be used to compute the soft shadows on the floor, because it's further than 1m. This will improve the results for scenes that are highly occluded, such as interiors.

SketchFX adds a totally new type rendering compared to AmbientOcclusion. While AmbientOcclusion is focused on creating renderings that are realistic enough, SketchFX creates renderings that are more artistic looking. It includes presets for pencil style rendering, watercolor, etc. We'll soon release a version of SketchFX that supports animation.

ntxdave

Thanks for the reply fluid. From what I read, I did not think SketchFX would be good for my type of model animation.

When I get some more time, I will mess with those setting even more but I think I did finally come up with something more acceptable.

JQL

@fluid said:

SketchFX adds a totally new type rendering compared to AmbientOcclusion. While AmbientOcclusion is focused on creating renderings that are realistic enough, SketchFX creates renderings that are more artistic looking. It includes presets for pencil style rendering, watercolor, etc. We'll soon release a version of SketchFX that supports animation.

SketchFX is really, really impressive! Well done on that!

fluid

Thanks! SketchFX can now be used with Animator; you can download the latest version here

I've posted a sample video on the gallery.

JQL

Sorry fluid, maybe I wasn't clear on that, but I don't own a copy of it though I think it's very cool!

I will definetelly consider it when I need something of the sorts though...