Flipping Crazy
-
Pilou,
I love this plugin from SDmitch, but it does unconventional things to the axis of the bolts it produces, causing a lot of axis alignment issues for me. I posted my issues in the Newbie Forum, see subject 'Flipping Crazy' for all of the screenshots.
Bob
-
I always don't understand all that!
As said previous in another thread
Seems the axe tools by Thomthom who give an axe to any objet
Then the replace component by Sdmitch Source / Target
makes that you want!
With that you have nothing to do!
No click for give orientation
What do you want more simple ? -
Pilou,
It's ok...I'm going to put this problem to bed. Thanks to all for your input
Bob
-
Only with Axes tool by Thomthom + Replace random component by Sdmitch!
(with only one component as source)
At the end just select all the ("component of 2 components" very easy with the Outliner)and explode them if you want refind the 2 original separated components!
And if you want a "resize on the Target"
use the special Replace random component file linked always by Sdmitch !
Very easy, very speedy and nothing to do!
-
Pilou,
Very cool
It's also very kind of you to share this. Thank you
Bob
-
Just a little thing that I have forgotten to write!
Between each call of the random replace component you must erase inside the Info Box all the Words Source and Target! (use again the Outliner for an easy selection)
If not the plug will not work in some cases! -
Pilou,
Since you put a lot of extra effort into this problem, I'm going to as well. First however, I have to be certain nothing is getting misunderstood by either of us.
I'll begin by asking you to use the BoltMaker XII plugin and (using the model I provided), try the following steps:
1 - open the file I've attached. It contains: a component (a block) with a bolt in it created using BoltMaker XII and a 'Source' component made by me.
2 - From the Window/Entity Info dialog box, confirm that the 'Source' bolt I created is a component. Double-click on the 'Source' component, you'll see that it's z-axis is pointing up (standard convention).
3 - From the Window/Entity Info dialog box, confirm that the bolt created by BoltMaker XII is a component. Double-click it and examine its axis. You'll find that the z-axis is pointing down. This is not standard practice as a new component should have the z-axis pointing up.
4 - Now run SDMitch's ComponentReplacement plugin against the 'Source' and 'Target' components.
What you should see is that the 'Source' component replaces the 'Target' component at a location and orientation you wouldn't expect.
Try this and let me know what you find. If you have a procedure I can follow that results in a properly oriented target replacement ( using the model I provided) ...I'll be ecstatic
.
Warm regards
Bob
Bob
-
Guys,
FINALLY...after listening to all of your ideas, I derived a solution based largely on your comments and it worked perfectly. When it happened, it was one of those cathartic moments.
The solution was mainly to forget all about trying to 'replace' a BoltMaker XII bolt with mine and instead, figure out how to 'insert' my custom bolt exactly where I wanted it in another component.
Steps followed:
1 - Selected my custom bolt component (the source).
2 - Using ThomThom's Axis tool, set the insertion point of the custom bolt x-y-z axis to 'center'
3 - Selected the Box component (the Target).
4 - Using ThomThoms Guide Tools plugin, set the Target's bounding box's cPoint at bound center.
5 - Click on the 'Source' component then CTRL-click on the 'Target' component.
6 - Using ThomThom's Guide Tools plugin, select Insert Component at cPoints.voila, the custom bolt is inserted in the block at the precise location I want.
THANK YOU ALL for your input
-
It appears you've got a process you're happy with. That's cool.
-
So you don't use a replacement mehod
Yes ...but how do you make when you have a little hundred of bolts in any orientation to change ?PS For me its' save as V6 or V7 for read the files
-
Hi Dave...
Forgive me if I already asked you, but could you remind me of the 'fewer' steps you use
.
I've had so much correspondence around this topic with so many people on different forums, I've lost track
Bob
-
Piloe,
Re "So you don't use a replacement method". Sorry to say, but I was going about this all wrong. I was using BoltMaker as a way to automatically create a bolt that would resize itself according to the dimensions of the target. I thought that by simply replacing the BoltMaker bolt with mine that it would be very easy to do. Sadly, I was wrong.
I do thank you for your efforts.
Bob
-
Bob, there are links on the first page of this thread. No plugins required the way I do it.
I'm curious about your procedure. You are locating the bolt so its center is aligned with the center of the block component. Why do you put a fastener in a single piece? Wouldn't that fastener be used to hold two parts together? And if that's the case, you don't want the center of the bolt located at the center of a single part, do you? What happens when you have a pair of bolts to locate on the part. Both of them can't be at the center in the part.
I would locate the insertion point for the screw in your example centered at the top of the head and place the screws at points on the surface of the part. These would be the points you'd identify in reality instead of points inside the part.
And with gluing, the bolts drop in easily in any orientation desired.
The only plugin used in the creation of the model in the video was to drill and counterbore the holes for the bolts. Everything else was done with native tools. It would be trivial to adjust the lengths of the bolts as needed so I didn't show that.
-
Maybe you can also look at Component Dropper by ThomThom
-
Hi Dave...
This is an excellent video tutorial. Thank you so much
. I would prefer your solution to mine if I can get it to work on BoltMaker XII output. You see, BoltMaker automaticaaly sizes the bolt to match its target.
Just one question: was the bolt you used created with BoltMaker XII and if so, did you manipulate it's axis in any prior to gluing them?
To answer your question "Why do you put a fastener in a single piece?".
Answer: To illustrate the 'flipping' issue I was experiencing when using BoltMaker XII. I totally agree that a single bolt in just one piece would serve no purpose
.
-
@bsintzel said:
Hi Dave...
This is an excellent video tutorial. Thank you so much
.
Ah. Thank you. I'm glad that was helpful.
@bsintzel said:
I would prefer your solution to mine if I can get it to work on BoltMaker XII output. You see, BoltMaker automaticaaly sizes the bolt to match its target.
Just one question: was the bolt you used created with BoltMaker XII and if so, did you manipulate it's axis in any prior to gluing them?
No. I didn't use any plugins to create the bolt. I just drew it manually. In this example I made the screw, washers and nut as separate components and made a nested component of them. When I made the nested component I set Gluing to 'Any' and clicked on the button to set the axes. I then placed the axes at the top of and centered on the head. It took little time to do the whole thing. I think I spent more time looking up the real dimensions for the head and socket than drawing the components. BUT I don't ever have to look that info up again.
Since the screw, washers and nut are separate components, I can easily get a parts list from the model if I want it.
@bsintzel said:
To answer your question "Why do you put a fastener in a single piece?".
Answer: To illustrate the 'flipping' issue I was experiencing when using BoltMaker XII. I totally agree that a single bolt in just one piece would serve no purpose
.
That makes sense. It seems to me that the boltmaker plugin currently creates more problems than it solves and forces you to be inefficient as you are working.
I now have a 1/4 in. socket head cap screw that is designed to sit with the top of the head flush to the surface of the part. It would be easy enough to edit its length or modify the location of the insertion point so I can have it insert with the washer on the surface. I could eliminate the washers or change the nut to a locking nut or whatever and do it all with only the native tools.
-
Dave R,
I 'really' liked the plugin you used to counter-bore. I design folding furniture that I ultimately make for myself so the counter-bore plugin you used would be a real time saver.
I found a suite of woodworking plugins https://sites.google.com/site/wudworx/plugins-and-tools/wwxboardmaker) and purchased the Wudworx Library Version 2(includes BoardMaker Pro, Dovetails, M&T, and Drill plugins).
I'm not sure if it's the same plugins you use. If so, you should get a kickback for semi-advertising their plugin
I can't thank you enough for the amazing support you've provided.
Warm regards
Bob
-
Bob, that's the plugin I used for the holes. I don't suppose you have much need for dovetails on your folding furniture but the Wudworx Dovetail plugin is perfect as is the M&T plugin.
I'm glad if something there was helpful.
-
Dave R,
Dovetails on folding furniture? lol...your right about that. Actually, I'm about to purchase a dovetail jig to add to my shop so the dovetail plugin is a perfect complement to it.
Bob
-
What dovetail jig do you have your eye on?
Advertisement