[Plugin]Draw Slope Normals.rb-v1.4-Mar 28,2013.

Ben Ritter

Thank you for your generosity.

Mra

Thank you x1000000000000000000000000000000000000000

This is much needed in sketchup and for you to share with the community is so nice. Levels in SketchUp wohoo!

Aureus

What kind of logic is applied for indicating z value?

When I have the cursor over a single spot (the end of a line) the z value is displayed and everything seems fine. But when the cursor is over a line sometimes lower value is displayed and sometimes higher - or in other words, once indicating the value of lower end and on other occasion on some other line indicating the value of its higher end.
So far I couldn't figure out what value is indicated when having the cursor over a face and in what relation it is to actual values of its edges.

When you have a line with 2 ends one having z value of 1.7 and the other having z value of 1.9, whatever figure is displayed (1.7 or 1.9) for it when you write down a new value (say 1.5) both ends have that new and same value, putting your line in horizontal position.

It seems this plugin has no respect to the groups as you can edit a group 'from outside'.

At the end I have one actual proposal. When you undo a step (you are not satisfied with the result of just put z value) - you are out of the command. Then you must run the plugin again. Can you make it provide you stay in the current command when you undo a step? My opinion is that it would speed up your workflow since it's a bit annoying and time-consuming starting the plugin again over and over after undoes.

tak2hata

Hi,
I update this to version1.3 in Mar 09,2013.
Add Toolbar.
and small improve.

Hi,Aureus.
The logic of modifying Z value is simple.
If you click Vertex it change z value of that vertex.
If you click Edge it changes z value of the vertices connencted to that edge.
If you click Face it changes z value of the vertices connencted to that face.

When the same positon of vertices clicked,The vertex in active_ editing group/component is preferred.
But the vertices are not same position,the vertex that near to camera is preferred.

Thanks.

mizar

it's wonderful
Thanks a lot

Lillioso

I get this error when i startup Sketchup, and the Plugin wont load.
What am I doing wrong?

tak2hata

@lillioso said:

I get this error when i startup Sketchup, and the Plugin wont load.
What am I doing wrong?

Hi,Lillioso.
I mistook about that "file_loaded".
It needs "require 'sketchup.rb' for first time.

I add the code,now in ver 1.31.

Thanks.

rv1974

There's some problem on 1.15- The arcs will be distorted (from plan point iof view).

tak2hata

@rv1974 said:

There's some problem on 1.15- The arcs will be distorted (from plan point iof view).

Hi,rv1974.
Watch this.Arc is not distorted in TOP View.

http://www.youtube.com/watch?v=h1YhuWG4NoQ

Please upload the picture or model that included "distorted arc."

pbacot

That's SPECIAL Tak2hata!

Thanks!

rv1974

Tak2hata-san, I tested it in deep and this tool indeed keeps the plan outline. This is
AMAZING!
About your last video: I played with the similar shape and the result was a bit distant from 100% perfect (the left example); then I reshaped the curves with Fredo's skinning
(the right example) and it was closer to the desired. Could you take a closer look at this issue?
REALLYThank you!
Offtop: yesterday I watched 'Jiro Dreams of Sushi' documentary. There are epic people in Japan!

left: draw slope
right: lofting (smoother result)

Untitled.skp

tak2hata

@rv1974 said:

Tak2hata-san, I tested it in deep and this tool indeed keeps the plan outline. This is
AMAZING!
About your last video: I played with the similar shape and the result was a bit distant from 100% perfect (the left example); then I reshaped the curves with Fredo's skinning
(the right example) and it was closer to the desired. Could you take a closer look at this issue?
REALLYThank you!
Offtop: yesterday I watched 'Jiro Dreams of Sushi' documentary. There are epic people in Japan!

Hi,rv1974.
Folding is works with Sketchup default function.
Freado' Skinning is smoother function.

I will connect to the skinning when fredo lib is loaded.

Offtop:Jiro's Sushi is expensive!I want to eat that!There is Great Sprits for Sushi!

orchard collie

Hi TAK2HATA
I'm using SketchUp 2013 Pro on Mac OSX 10.8.4 - downloaded the plugin and unzipped it into the Plugins Folder.
Opened SketchUp went to Preferences - Extensions - Install extension - located the folder', opened it but could not select the draw slope normals.rb file to install it.
Any ideas what my problem is, apart from stupidity?
Cheers

tak2hata

@orchard collie said:

Hi TAK2HATA
I'm using SketchUp 2013 Pro on Mac OSX 10.8.4 - downloaded the plugin and unzipped it into the Plugins Folder.
Opened SketchUp went to Preferences - Extensions - Install extension - located the folder', opened it but could not select the draw slope normals.rb file to install it.
Any ideas what my problem is, apart from stupidity?
Cheers

Hi,orchard.

Installing plugin was completed when you unzipped it into the Plugins Folder.

In case of installing from "*.rbz" file,
"Install Extension" in Preference menu works.

Thanks.

rv1974

Tak2hata, could you please implement somehow the 'offset' (or let's call it 'local') coordinate input? Say typing evenly + 50 would move the vertex 50cm upward from the currentposition.
In many situations it's more natural to work with local coordinates.
Thanks in advance
P.S. This tool in conjunction with Fredo's Skinning make killing combo in landscape\road design!

orchard collie

Thanks Tak2Hata
Assuming it's loaded, I can't seem to locate the plugin in any of the Menus or by context clicking a mesh.
Any suggestions as to how to activate it on Mac?
Thanks
Orchard Collie

tak2hata

Hi,orchard.
Download plugin zip file and unzip.
rb file and the folder include some file will be created.
unzipped with folders
Please place all files to plugins folder.

The command will be shown in [MENUBAR]->[PLUGINS]->{DRAW SLOPE NORMALS]
and [TOOLBAR]->[Draw Slope NormalsTOOL]

Thanks.

finitylab

this is superb.

gvatnar

Thanks for a great plugin!!

bsfranza

hi there together
still a great plugin - however i wonder if its possible to edit the script so it shows the slope in percentage? and i wonder if it would be possilbe to modernise it so it uses the overlay function of the latest sketchup??

if anyone can helpt me i would be very happy - im currently trying to edit it on my own with some help of the infamous chat gpt - but from i learned in the forum this is not said to be very effective ...

will see if anyone can help, im willed to share some cookies ofc!

best
fa