Podium V2 interior
-
New one. Tad too gloomy, me thinks. 36 mins for a 5000 x 2694 render -not bad.
-
just show some light coming out of that fixture over the island, and you've got a winner there.
-
Nice work, 36 mins what are you running on ?
The floor looks nice is that lots of tweaking, can you give us a run down of how you got to this quality. -
looks good....really like the atmo.
-
The wall opposite the island looks like it could use a cool piece of art.
-
@unknownuser said:
The wall opposite the island looks like it could use a cool piece of art.
I was thinking the same thing, although I'd possibly opt for 4 or 5 equally sized works rather than one big one. I suspect that would work best.
I should also up the lamp's polygon count.
-
Thanks, lads.
David -yes, I should do that, shouldn't I? I'm quite keen to find out what Podium light would work best in this case.
Congellous -I'm using a 4 or 5 year old Mac Pro. The floor is a mat from Podium's Component Browser. Podium's mats are pretty straightforward. There's reflection, bump, and a blur tickbox. That's it. There's some stuff on mats over at http://www.suplugins.com. Pretty much all you need to know.
After the render finished, I took it into Photoshop, lowered the saturation of the yellows and the reds, added a curves layer, sharpened the image up using the high pass filter, did some manual blurring, and added a blueish cast to the right of the image. Then I downsampled it.
If I remember correctly. My postprocessing tends to be capricious rather than methodical.
-
-
I could do a version with Thea ... if there were interior rendering presets available to pick apart.
-
@unknownuser said:
I could do a version with Thea ... if there were interior rendering presets available to pick apart.
For biased rendering? I'd start from "04. Final Gathering" preset and improve quality if needed. Or perhaps new Adaptive (AMC) from interactive renderer, as it's fairly fast if bias is set high (also enable caustics for better light).
-
Hm, I'll try that. Thea's biased engine is still somewhat of a mystery to me.
-
@unknownuser said:
Hm, I'll try that. Thea's biased engine is still somewhat of a mystery to me.
You could try this Adaptive (BSD) -preset. Save in "C:\ProgramData\Thea Render\Presets" in Win7. If it feels too slow, downgrade settings towards "04. Final Gathering" -preset. Also you can disable or tune down "Ambient Occlusion" under Render | Biased RT, if it disturbs.
Also some material tuning may be needed. Under material general, set Perceptual Level(%) to 10,000 if your material has textures (higher will give better quality but difference is small as textures do hide imperfections) also if you have glossy materials you can set they Tracing Depth to 8-12 (if some black areas appear as result of too low tracing depth).
-
Tom
Can you share the model? I'd like to play with Thea's biased engine to see what speeds I can get...when I get the time.
-
Pentti -thanks!
Pete -of course. Tomorrow, after I've dropped of Wee Satan at school. I'll have to take the wall and floor textures out, though -they're from the non-free section of the Podium Component Browser. Did I notice familiar looking plants in there, btw?
In the meantime, here's a version with the lamp switched on.
-
Looks fantastic Tom. As for the "art on the wall" you can use your own prints.
-
I tried that. Looked "meh".
So ... it's done. -
Tom,
Firstly thanks for pm'ing me the .skp, Notareal sent me the link to the original model here: http://www.3dallusions.com/Site/Vault/ArchModels/Kitchen_SKP.zip which by the way is horrible as it is totally out of proportion, off axis and spends way more poly's than it needs, yours is nicely optimised...thank you.
On opening yours I noticed your setup, which I believe is way more relevant than any render preset/setup. You have used L.E.M's in order to mimic exterior light as well as one to give light behind the camera.
I was instantly reminded of my days with Podium 1 and remember this being the best way to get soft shadows and good even lighting, however I wondered if this was the fastest way (I cannot remember) did or does LEM's come at a speed cost?
Does Podium 2 have HDRI support? as I was wondering if deleting the exterior LEM and using Image based lightning would not be faster with even better soft lighting?
I'm assuming the LEM behind the camera is to assist and give some light volume as without it all surfaces facing camera would be black, however I am wondering if there was a way of using ISO, shutter speed and f-number settings to enhance lighting without the need for the LEM?
What my rambling is about is the setup of scene may actually be just as if not more important than the actual render settings.
-
@unknownuser said:
I tried that. Looked "meh".
So ... it's done. On second thought. . .I like it this way. It has a very monastic feel to it. A sort of hypo-Tech Austerity that I find appealing. I think putting a big Andy Warhol or worse a Patrick Nagel
on the wall would be a bit of a cliche. -
If two chairs and two apples, then loneliness could be more obvious.
Three chairs? three apples? We all are Stanley Kubrick's funs, aren't we?
This is a "strong" image. Well done.
It's the Ps work that I don't like much. A fake-volumetric effect could turn the scene to a more dramatical way. -
Who lives here ? Mystery is complete!
Advertisement