[Plugin]T2H_BuildingStructureTools2.2.4 in20141207

tak2hata

@unknownuser said:

Hello

After installing V 1.0a, I have the following error code. Not sure why.

Thanks in advance for your plugins and help

Ken

Tak2hata

Thanks for the update 1.1b. It fixed the above illustrated error. However, I notice now, that the beams selection will not make any beams that are vertical. It will make beams close to vertical but not exactly 90 degrees. As close as I can get to vertical is 0.067 degrees off vertical. I didn't see this problem on the first version.

Again thanks for the quick response on the other error.

Ken

Hi,Ken.

I want to see your description as picture.and parameters in webdialog.

And I have an elementary question.
"degrees" is units of distance?
In my country ,distance is decimal.so I'm not used to be the degree as distance.
Does 90 degrees equal to 1/4"?

Thanks.

ken

The three illustration show a yellow background rectangle, 2'wide by 10' tall. Starting at the bottom at the center line closest I can get the 4x13 I beam to vertical is 9/64 off the center vertical line at the top. So right now I can not draw any beams exactly vertical.

Hope this helps.

Ken

ScreenHunter_32 Jul. 17 06.58.jpg

ScreenHunter_33 Jul. 17 06.58.jpg

ScreenHunter_34 Jul. 17 06.59.jpg

SUFractal

@unknownuser said:

The three illustration show a yellow background rectangle, 2'wide by 10' tall. Starting at the bottom at the center line closest I can get the 4x13 I beam to vertical is 9/64 off the center vertical line at the top. So right now I can not draw any beams exactly vertical.

Hope this helps.

Ken

Ken:

For comparison's sake, I did a similar test and do not seem to have an issue with true verticality. I used the 'column' tool and my column was 12'-0" tall. I noticed that you used the term 'beam' ... are you by any chance using the beam tool to try to draw a vertical line as a column? Is that perhaps the cause?

SUFractal

ken

Well yes, I am using the beam tool, along with the "bar, T-bar, pipe, angles and beams" None these selection will make a vertical object. Note, zooming in for a real close view, I can see that as long as the top (note going from the top to bottom doesn't make a difference) selection point is outside the area where the point will be snapped to the vertical I can make any of the above objects. However, if I let Sketchup snap take over and the point is snap to a vertical position, than the program will not make the selected object, "beam, bars, pipe angle or beams". See the attached file.

Ken

Vertical Test Ken.skp

tak2hata

@unknownuser said:

Well yes, I am using the beam tool, along with the "bar, T-bar, pipe, angles and beams" None these selection will make a vertical object. Note, zooming in for a real close view, I can see that as long as the top (note going from the top to bottom doesn't make a difference) selection point is outside the area where the point will be snapped to the vertical I can make any of the above objects. However, if I let Sketchup snap take over and the point is snap to a vertical position, than the program will not make the selected object, "beam, bars, pipe angle or beams". See the attached file.

Ken

Hi,Ken,SUFracatal.

I understand this problem.

This is mistake of mine.

I want to limit the drawing wall as vertical.(It make error certainly.)
But this code is not so.

I will fix this bug later.Now I am out of my computer.
Sorry,Please wait.

Thanks.

guanjin

未命名.jpg
tak2hata:
Thank you for your hard work
How to disappear other tools? icons, language change does not completely!
Click on the icon does not work

tak2hata

H,All.
I update this.
...KEN.
BUGFIX :about create nothing when clicks points as Vertical.
It will clear the problem.

...guanjin.
Laungage .......
Wait deadly tried me.
or You can change word as you like If you can edit html.

@guanjin said:

How to disappear other tools?

It is more convenient to be both?
or If it is both, what will be troubled?

@guanjin said:

Click on the icon does not work

I can not know what makes problem from that text.

Good night.

ZFRPS

tak2hata:
about create nothing when clicks points as Vertical,
in v1.1d not clear,
please try one times it ;

Thanks again !

tak2hata

@unknownuser said:

tak2hata:
about create nothing when clicks points as Vertical,
in v1.1d not clear,
please try one times it ;

Thanks again !

Hi.
At first,when working with the class "wall" ,you can not pick second point to vertical.

I need to know more detailed information if this is not your case.

Screen shot of setting inBst dialog.
The axis the slope directing to.(x,y,z)
The message Ruby console shows when the error is exists.
I want to see the two picked points were truely vertical.

Please reply about lines above.
Thanks

ZFRPS

Dear tak2hata:
This my test,please try it again !
Your this plugin already very powerful,I wish it change more powerful

  thanks again!

tak2hata

@unknownuser said:

Dear tak2hata:
This my test,please try it again !
Your this plugin already very powerful,I wish it change more powerful
[attachment=3:22lfhpqk]c01.jpg[/attachment:22lfhpqk][attachment=2:22lfhpqk]c02.jpg[/attachment:22lfhpqk][attachment=1:22lfhpqk]c03.jpg[/attachment:22lfhpqk][attachment=0:22lfhpqk]c04.jpg[/attachment:22lfhpqk]
  thanks again!

Hi,zfrps.
"MWALL" is not able to create automatically from curves.
I will test "COLUMN" auto create.

@unknownuser said:

tak2hata:
about create nothing when clicks points as Vertical,
in v1.1d not clear,
please try one times it

Does this reply mean this problem?

Thnx.

ZFRPS

Dear tak2hata:
Yes!
Especially about automatically created "column ";before it's nice,now it need strengthen.

Thanks!

tak2hata

Hi,zfrps and all.
I update BST version to 1.1e.
Bugfix about auto creating columns.
And improves.

BST becomes nice tool step by steps.

Thanks.

ZFRPS

tak2hata:

Maybe only need keep one of dialog box!

ZFRPS

tak2hata:

now, a times only can choose one entity or face,Whether it can be a much choose?

moreover, have extend to face already,so maybe show to face no need !?

Thanks!

ZFRPS

Dear tak2hata:
However,I still have some ideas to speak out,Because I love too the plugin,I believe that your this plugin will produce very big help to BIM.

1. **grow to face** only useful for "Z",but for **MWALL** is invalid;
2. The shape of the face for ladder;**grow** or **extend** is invalid too;
3. One-time much choose can greatly improve the efficiency of the modeling.
....

THANKS AGAIN !

Heven7_floor

@unknownuser said:

Very powerfull tool, this very very usefully for construction with sketchup, Thanks Tak2hata, your creative brough the good things come to other

SUFractal

tak2hata:

I have what I hope is a simple question. How do I change the color of any beam, column, etc. before placing/drawing it? In the webdialog box, the option default is black. No matter which color I type into the box, the color remains a light blue color.

Thanks,

SUfractal

tak2hata

Hi,
I am too busy.So I can not improve my plugins.

Multiple "Grow to face" will be added.

I will consider applying "Grow" for "MWALL".

@sufractal said:

tak2hata:

I have what I hope is a simple question. How do I change the color of any beam, column, etc. before placing/drawing it? In the webdialog box, the option default is black. No matter which color I type into the box, the color remains a light blue color.

The color is material.
Beams material is created from "FRONT FACE MATERIAL" and "BACK FACE MATERIAL".
It appears random color when the materialnames in "FRONT FACE MATERIAL" and "BACK FACE MATERIAL" is not existed in sketchup model.

So you may set sketchup templete with the materials.

Thanks.

SUFractal

That makes sense!

Thanks.

@sufractal said:

tak2hata:

I have what I hope is a simple question. How do I change the color of any beam, column, etc. before placing/drawing it? In the webdialog box, the option default is black. No matter which color I type into the box, the color remains a light blue color.

The color is material.
Beams material is created from "FRONT FACE MATERIAL" and "BACK FACE MATERIAL".
It appears random color when the materialnames in "FRONT FACE MATERIAL" and "BACK FACE MATERIAL" is not existed in sketchup model.

So you may set sketchup templete with the materials.

Thanks.[/quote]