Curved Walls
-
just take these techniques and run with them you can refine it as much as you like but the principle concept remains the same. for example you could soapskinbubble (plugin) the top edge.
but you're the only one that knows exactly what you want.
-
thanks so much everyone
i want it to look exactly like the one that jeff did, but with a little more dip, very smooth and very clean, not sure what he means by it not being clean geometry, looks clean to me
now i just have to figure out how to do what he did
i will definitley play with the soapskinbubble plugin though, that looks like a cool plugin
-
-
Look for Earthmover's Garden Wing wall tutorial a page or two down in the tuts section. I could look it up and post the link for you but... It's good.
There should be a permanent sticky(?) on how to do curved walls, ramps etc. in this Newbie section. Isn't that one of the most FAQ's. Heck, a "curved wall tool" should be added to Sketchup along with a "circular stair tool."
-
@xrok1 said:
how about this:
quote="xrok1"]how about this:
@xrok1 said:how about this:
/quotealmost perfect, i need the transition where the dip starts to be smooth, an arc not an angle see the attached drawing where i drew an arc on your wall you did on one side, if i could make that transition smooth, that would would great
kind of like the wall is smoothly undulating up and down
-
-
@xrok1 said:
see if you can take it from here:
thank you so much, do you mind briefly explaining what you did?
-
@rudbeckia said:
@xrok1 said:
see if you can take it from here:
thank you so much, do you mind briefly explaining what you did?
well i've been trying to do this with no scripts, and it can easily be done, but alas i ran out of patience.
so i use ToolsOnSurface to draw the arcs, then i used extrudelinetool to stretch it out ,using the top edge that you where trying to get rid of as a guide. then of course you took it from there, selecting everything, doing a intersect model and deleting the junk you don't want.
-
@xrok1 said:
@rudbeckia said:
@xrok1 said:
see if you can take it from here:
thank you so much, do you mind briefly explaining what you did?
well i've been trying to do this with no scripts, and it can easily be done, but alas i ran out of patience.
so i use ToolsOnSurface to draw the arcs, then i used extrudelinetool to stretch it out ,using the top edge that you where trying to get rid of as a guide. then of course you took it from there, selecting everything, doing a intersect model and deleting the junk you don't want.
last question promise
my toolsonsurface tool palatte does not have an arc tool, how are you drawing the arc on the curved surface and I am assuming extrudelinetool is a ruby I can download?
-
@unknownuser said:
last question promise
my toolsonsurface tool palatte does not have an arc tool, how are you drawing the arc on the curved surface and I am assuming extrudelinetool is a ruby I can download?
hey, no problem, i didn't mean to imply i was running out of patience with you. just with the file.
toolsonsurface ver1.31
the tool is circled in red.
extrudelinetool extrudelinetool.rb i don't know if i'm supposed to attach this, but it was free and i can't find where i got it from so...
PS, i would highly recommend you don't use SU without this http://www.sketchucation.com/forums/scf/viewtopic.php?f=180&t=6708&st=0&sk=t&sd=a&hilit=extrude
-
All that can be made with only intersections of cylinders & tubes!
-
Qui
Pilou, how's development going over at Moi, is there a public beta for ver.2 yet?
BTW, can you explain your moto i've always wondered WTF "Is beautiful that please without concept!", means.
-
@xrok1 said:
Qui
Pilou, how's development going over at Moi, is there a public beta for ver.2 yet?
BTW, can you explain your moto i've always wondered WTF "Is beautiful that please without concept!", means.
my tool on surface tool bar is not the same as yours?
-
thats weird your jointpushpull tools aren't the same either?
are you sure you have the latest versions?
PS, did you notice you have like three sets of the same tools scattered all over the place?
-
@xrok1 said:
thats weird your jointpushpull tools aren't the same either?[attachment=1:1vez1evq]<!-- ia1 -->Capture.JPG<!-- ia1 -->[/attachment:1vez1evq]
are you sure you have the latest versions?
PS, did you notice you have like three sets of the same tools scattered all over the place?[attachment=0:1vez1evq]<!-- ia0 -->Capture2.JPG<!-- ia0 -->[/attachment:1vez1evq]
i got them from here http://www.crai.archi.fr/RubyLibraryDepot/Ruby/em_arc_page.htm
i am new to SU ruby/plugin world, how do i know if i have the latest?
lol!!! i do have to many tools every where, i shall fix that
-
don't make me come over there.
i use without CADfather icons
http://www.sketchucation.com/forums/scf/viewtopic.php?f=180&t=11212&p=76625#p76625http://www.sketchucation.com/forums/scf/viewtopic.php?f=180&t=6708&hilit=JointPushPull
-
@xrok1 said:
Pilou, how's development going over at Moi, is there a public beta for ver.2 yet?
I trolled the MoI forum the other day and noticed that Pilou is an ardent SketchUp evangelist over there. Regarding your question, it seems they've been in closed beta since September:
http://www.google.com/cse?cx=004480280974618486967:rqgfj4-y60a&q=v2&sa=Search -
thanks, i've been anxiously awaiting ver.2 for a while now. i love the program it just needs a few more things to make me buy it. maybe ver.2
-
@rudbeckia said:
not sure what he means by it not being clean geometry, looks clean to me
it's just random.. nothing really matches up.. there's no system.
sloppy:
clean:
-
@unknownuser said:
@rudbeckia said:
not sure what he means by it not being clean geometry, looks clean to me
it's just random.. nothing really matches up.. there's no system.
sloppy:
[attachment=2:1wl1qjcn]<!-- ia2 -->sloppier.jpg<!-- ia2 -->[/attachment:1wl1qjcn]clean:
[attachment=1:1wl1qjcn]<!-- ia1 -->cleaner.jpg<!-- ia1 -->[/attachment:1wl1qjcn]that looks perfect!!!! which tools did you use for that, it looks great!
Advertisement