ThruPaint Slow and Rotating tool not working
-
@mergaite said:
I don't have any other performance issues and 'native' texture position tool of Sketchup works fine. I am actually using Sketchup 2017. The problem is that it takes around 30min to apply the material on complex faces and when trying to rotate the texture it totally freezes or moves but doesn't do anything.
With ThruPaint, do you get bad performances with any texture, like the built-in textures of carpets or brick wall, or just with some of your custom textures?
-
both, custom and built-in.
-
Thanks.
I guess this happens with any model? Is that the case
-
Yes, still persists. With any model any texture. To apply texture is a bit pain but not as bad (just a bit time consuming) the worst is the rotation. If it is applied correctly it's ok but if I have to position it. It totally freezes and it doesn't show on the screen that the texture is being rotated.
-
@mergaite said:
Yes, still persists. With any model any texture. To apply texture is a bit pain but not as bad (just a bit time consuming) the worst is the rotation. If it is applied correctly it's ok but if I have to position it. It totally freezes and it doesn't show on the screen that the texture is being rotated.
If you take a simple isolated face and apply a texture with ThruPaint, and then rotate, move, etc..., do you get a performance issue?
I try to understand if the problem is due to a particular context or is general to your Sketchup setup, as it works fine for me, and apparently no other user has reported a similar issue.
-
Actually, just tried on a simple box and everything works fine, rotation has no issues. But on a simple cylinder again doesn't work. I guess it's only on complex faces it's an issue. Is there something I can do with my models to fix it?
-
@mergaite said:
Actually, just tried on a simple box and everything works fine, rotation has no issues. But on a simple cylinder again doesn't work. I guess it's only on complex faces it's an issue. Is there something I can do with my models to fix it?
Don't know what happens for you specifically, as no other user is signaling the problem so far.
On a small cylinder, this should be fast as well as this is not a complex surface. And also, it used to work fine for you in the past.Maybe, you can change some OpenGL parameters in Preferences to see if it changes something. Bec careful to save your model, because you often get a bugsplat when changing the OpenGL parameters.
Fredo
-
Thank you so much for your input, Fredo. I really appreciate it.
I guess it comes down to my computer settings. I will check it out.
-
I have this problem to. If I change "Use fast feedback" option > click "Materials" (ThruPaint Auto activate is on) > instant bugsplat.
Orbit with middle mouse button also buggy now
-
is thru paint still working?... because everything in the tool under freedo is working except the thru paint. there is no option bar pop out after I select the tool.
-
@ianpillars55555 said:
is thru paint still working?... because everything in the tool under freedo is working except the thru paint. there is no option bar pop out after I select the tool.
Can you open the Ruby console before you launch ThruPaint to check if there are error messages.
-
hello / salut,
Same problem Here, with sketchup 2018.
I noticed that if I disable vray it's slightly better. I tried on the very same geometry (a simple vase) in sketchup 2013 it takes 1 sec. in 2018 it's 10 secs with vray disabled, 2+mins with vray enabled
Paul
-
@grabuge said:
I noticed that if I disable vray it's slightly better. I tried on the very same geometry (a simple vase) in sketchup 2013 it takes 1 sec. in 2018 it's 10 secs with vray disabled, 2+mins with vray enabled
Could you send me the model so that I make tests. There should be no reason why there is a difference between SU versions.
The problem with Vray is another story however.Fredo
-
ok j'ai envoyé par PM
merci
Advertisement