sketchucation logo sketchucation
    • Login
    ℹ️ Licensed Extensions | FredoBatch, ElevationProfile, FredoSketch, LayOps, MatSim and Pic2Shape will require license from Sept 1st More Info

    Model Review and suggestions.

    Scheduled Pinned Locked Moved SketchUp Discussions
    sketchup
    12 Posts 3 Posters 636 Views 3 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • R Offline
      rkitect
      last edited by

      I was just about to reply stating that my problem with the follow me tool is that I couldn't get the curves to close to the adjoining face:

      http://gibsonhh.info/revit/video/sketchupArcExt.png

      I see in your model you were able to do this. Which curve did you follow to get it to close like that?

      Thanks,
      -rkitect

      1 Reply Last reply Reply Quote 0
      • jeff hammondJ Offline
        jeff hammond
        last edited by

        i did it with a 1/4 circle (of which some of it is still visible.. it's the line inside the cabinet.)

        in certain instances, it works better if you run your follow me path longer then needed before using the tool.. use a surface to cut it via 'intersect with model'

        i'm not the best with words and i can do a drawing that will explain it but i have to go eat dinner now.. if no one has cleared it up by the time i get back, i'll sketch something up for you..

        dotdotdot

        1 Reply Last reply Reply Quote 0
        • R Offline
          rkitect
          last edited by

          I understand what you're saying. Trying to figure out a way to extend the curve I am using, but it looks like I'm going to have to redraw it. I'll let you know how it works.

          Thanks again,
          -rkitect

          1 Reply Last reply Reply Quote 0
          • jeff hammondJ Offline
            jeff hammond
            last edited by

            maybe a weird way to go about it but this style is based around tig's invert_selection move at the end..

            sort of just freestyled the dimensions but the proportions are similar..

            movie link:
            http://homepage.mac.com/jeffhammond/.Public/cabinetthing.mov

            .


            cabinetthing.skp

            dotdotdot

            1 Reply Last reply Reply Quote 0
            • jeff hammondJ Offline
              jeff hammond
              last edited by

              the follow me tool will work well IF...

              the top is supposed to look like this:
              Picture-2.jpg

              instead of this:
              Picture-1.jpg

              [note - top corner of cabinet]

              dotdotdot

              1 Reply Last reply Reply Quote 0
              • R Offline
                rkitect
                last edited by

                I tell you what, I'm getting the concept but I always end up with missing faces after I get the initial mass going, and usually retracing the boundaries of the faces don't result in a new face. Any suggestions on something specific to look for?

                Attached is an updated model. I tried attaching a pic, but couldn't figure out how to make it resize like in the previous poster 😕

                Picture 4.png

                Thanks again,


                EPA TAke3.skp

                1 Reply Last reply Reply Quote 0
                • jeff hammondJ Offline
                  jeff hammond
                  last edited by

                  @rkitect said:

                  but I always end up with missing faces after I get the initial mass going, and usually retracing the boundaries

                  when you zoom into your drawing, it starts getting pretty messy...

                  bottom right corner:
                  Picture-1.jpg

                  zoom in further:
                  Picture-2.jpg

                  that's the problem with the follow me tool and/or the way sketchup draws radii... you'll notice in the movie i did that i extend my follow me path on both sides so i can cut/add a fresh edge to both sides..
                  you have to keep things clean and simple or the hours of head scratching start to add up..

                  dotdotdot

                  1 Reply Last reply Reply Quote 0
                  • R Offline
                    rkitect
                    last edited by

                    That's what I'm finding, but with a deadline quickly approaching, I'm going to have to get over my 3dmodel OCD and just get-er-dun. I have noticed that the model gets progressively sloppier as I keep trying to modify the faces after the follow me. Just going to take some practice.

                    Thanks for your help!

                    -rkitect

                    1 Reply Last reply Reply Quote 0
                    • R Offline
                      rkitect
                      last edited by

                      Wanted to get some suggestions for the second part of my model. I was wondering how other users would form this shape in SU:

                      http://gibsonhh.info/revit/video/sketchupForm1.swf

                      Thoughts and suggestions gladly welcome!

                      Thanks again

                      -rkitect

                      1 Reply Last reply Reply Quote 0
                      • R Offline
                        rkitect
                        last edited by

                        Any suggestions on how to create a void in a surface that was created with Sandbox?

                        1 Reply Last reply Reply Quote 0
                        • 1 / 1
                        • First post
                          Last post
                        Buy SketchPlus
                        Buy SUbD
                        Buy WrapR
                        Buy eBook
                        Buy Modelur
                        Buy Vertex Tools
                        Buy SketchCuisine
                        Buy FormFonts

                        Advertisement