[Plugin] CenterPointAll.rb

Jim

Hi David,

the API supports getting the center of an ArcCurve object. Once a curve is exploded, it no longer has a center (according to the API.)

What I typically do is create a new 2-segment arc over 2 of the existing segments - in essence tracing over 2 of the existing segments. Then you can use Arc Centerpoint on that arc.

david_h

@tig said:

If you weld lines into a curve there's no guarantee that that 'curve' will have a 'centre' at all (draw some connected lines and weld them into a curve - where's its centre ?). So, if you have an exploded arc don't weld it back into a curve (an arc is a curve but a curve isn't an arc): just redraw the arc and then it WILL have a centre...
The following are different animals...CenterPoint marks the 'centre of gravity' of the selection.
My CenterPointAll marks the centres of all selected objects individually.

.

Understood, hence the question. However this CenterpointALL sounds intriguing. WHere does one find this?

thx

david_h

I got the Centerpointall.rb. It's a good one , but not exactly doing what I need. It enabled me to do a workaround for my specific case, but I guess what is needed is a script that will find the Radius point of an arc even if SU doesn't recognize it as an arc per se.

plot-paris

so basically you need a "geometric shape recognizer".

that would be a wonderful thing, by the way. imagine you have a complicated curved form consisting of loads of small lines and SketchUp simplifies it into (for example) three curves.

the plugin could have some correction-freedom settings too. for example if it recognizes two arcs in a shape which connecting bits are almost tangential, SU could correct the position of the connectin point slightly to match a perfect tangent...

that would be awesome!

david_h

Oui! C'est Ca! Where are these RUBY GURUS when you need them? (jk)

Im sure they don't have anything else to do but respond to my whining.

JClements

When I have time, I often draw over "apparent" arcs and circles because I can then use Entity Info to verify radii of piping and to facilitate the extrusion of smoothed-surfaces and improve exporting .SKP's to other formats.

I think the bottom line is you'd need a basic script (using the model context or selection) to find series of contiguous segments, then analyze them to determine if they have the characteristics of an arc.

For instance: are all segments of equal length and are all of their common angles equal (there may be more conditions that I haven't thought of)? If all segments touch one another, then are they a polygon or a circle?

If such a script can be developed, then it could be used as a common routine called by other scripts such as pipe-along-path or used on intersected geometry. Once the script qualifies the segments, it could then automatically redraw them, make centerpoint guides, etc.

david_h

Yeah. . .what he just said. .. uh Huh. I think

Anyway. .. I just want to find the Radius point of any curve be it arc or no. anything else, above that . . ..Gravy.

plot-paris

JClements, that would be a damn handy tool and a wonderful addition to the weld-script...

watkins

Dear David_H

You can use the protractor to find the centre of an arc or circle. Snap the tool to the mid-point of a segment and then click on the end of that segment (you have a choice of two points). Rotate the protractor 90 degrees to create a construction line along the segment's normal (located at mid-point). Repeat for a second segment. The centre point is marked by the crossing of the construction lines.

A ruby script might work in the same way.

Activate the tool, and moving either clockwise or anticlockwise (but not both):

Click first end point, segment 1
Click second end point, segment 1
Click third end point, segment 2
Click fourth end point of segment 2
Ruby computes equations of normals at mid-points of segments 1 and 2
Ruby computes coincident point to yield x,y,z value of centre point

Variations:

Segments 1 and 2 are start and end segments of arc = redraw arc (input = number of segments)
Segments 1 and 2 are connected = redraw circle (input = number of segments)

I am not a script writer, but the above would seem do-able.

david_h

Watkins. Yeah, I had been doing that. I was just hoping for a one-click solution. Cuz I ain't no Ruby Writer Neither. . .sigh! But thanks for the input.

Jim

@unknownuser said:

Watkins. Yeah, I had been doing that. I was just hoping for a one-click solution. Cuz I ain't no Ruby Writer Neither. . .sigh! But thanks for the input.

Dave,

You might have more luck if you start a new request thread in the Ruby forum.

rosbourne

Thanks.. Now more easier to make center point

ship69

Does this video have sound? It's coming out silent on my PC.

Dave R

@ship69 said:

Does this video have sound? It's coming out silent on my PC.

No. It's a silent video.

Einstein

Thanks TIG

This simple tool helps me rotating components around their centerpoints which is quite complicated in SU.

It would be even more handy if a created centerpoint was interactive, I mean: changed with scaling and moving component or group it's based on. But I realise that would be also much more complicated code.

Box

@einstein said:

rotating components around their centerpoints which is quite complicated in SU.

To rotate about the midpoint of a group or component, use the rotation handles that appear when you use the Move tool.

sarkarshomit

Can't get it working in sketchup 2018.working fine in skup16, but not in 18...any help if i am doing something wrong!!

Dave R

@sarkarshomit said:

Can't get it working in sketchup 2018.working fine in skup16, but not in 18...any help if i am doing something wrong!!

Evidently you are doing something wrong. I just installed it in SU2018 and ran it. It works fine. How did you install it? Where did you install it? Do you have Guides set to show in the View menu?
Result of CenterPointAll

sarkarshomit

@dave r said:

@sarkarshomit said:

Can't get it working in sketchup 2018.working fine in skup16, but not in 18...any help if i am doing something wrong!!

Evidently you are doing something wrong. I just installed it in SU2018 and ran it. It works fine. How did you install it? Where did you install it? Do you have Guides set to show in the View menu?
[attachment=0:9qktjmkx]Screenshot - 5_16_2018 , 5_31_16 AM.png[/attachment:9qktjmkx]

Thanks for the help.

Strangely in skup16, the plugin shows up in plugins menu named as "set centerpoint".
And in skup18 it shows up in extensions menu as "Add centerpoint".

So finally its working for me. Thanks again.

Box

Sounds like you may have had a different extension installed in 2016. There is one called Set Centerpoint.
Tig's shows for me in 2016 as Add Centerpoint.