3D Truss Models

pilou

don't know if SketchUp has parametric capabilities. Any thoughts on this?

With Dynamic Components or heavy ruby coding?

medeek

Version 1.0.6 - 10.25.2015
Added floor truss type, Modified Warren - System 42.
Metric input enabled for floor truss types.
Top and bottom bearing option enabled for left and/or right end of floor trusses.
Ribbon cut option (top) enabled for left and/or right end of floor trusses.

One central chase that can be position relative to the left end of the truss. If the chase becomes closer than 1/4 the span to either end it will flag the user and re-position. Also some logic to check the chase size to span ratio and absolute max. chase size (24").

System 42 or 32 floor trusses using the modified warren configuration which seems to be the most popular for this type of floor truss. Top bearing configuration includes an additional slider for extra strength and a vert. Note the change in diagonal directions when comparing a top to bottom bearing floor truss, I was not aware of this until studying them in some detail. Typical panel length is 28" but this can also be set by the user to any value.

I figure if you need more than one chase it isn't to hard to manually edit the component and copy a couple of the vertical members over and then trim out the diagonals.

medeek

@pilou said:

@unknownuser said:

don't know if SketchUp has parametric capabilities. Any thoughts on this?

With Dynamic Components or heavy ruby coding?

I've been looking at dynamic components and the API documentation seems rather sparse. There are a number of forum posts on this topic but so far it seems to be just beyond my grasp.

medeek

Floor trusses 40' span, 60' bldg. length, 24" deep.

Notice these are top chord bearing trusses with the diagonal webs reversed from the bottom bearing trusses in the previous post, this is by design.

medeek

Various configurations of a vaulted or cathedral truss:

medeek

Various configurations of dual pitch trusses:

driven

have at look at "parametric_grid.rb" and "parametric.rb" from sketchucation Plugin Store...
john

medeek

@driven said:

have at look at "parametric_grid.rb" and "parametric.rb" from sketchucation Plugin Store...
john

Thank-you for the information. I will be looking into this further.

After using the housebuilder plugin and my own I've determined I am lacking in two areas:

Post Configuration: Ability to modify the component once it is created. It would be nice to make it a dynamic component and adjust any and all variables.

Positioning: It would be really nice to drop the truss set right into place by clicking the location with the mouse.

medeek

Using the Medeek Truss Plugin and the housebuilder plugin I was able to create this simple model in about 3 minutes:

I would like to be able to create this type of model in the future:

This model was created in Solidworks and probably took a day or two to assemble. Notice the gambrel attic and the gable end trusses. That ability I would like to add into the plugin.

This next model was also created in Solidworks and only shows the foundation and framing, the entire model represents about a month of work including the drawing set.

I would like to see a plugin that is capable of generating this level of structural detail in a couple of hours instead of weeks. Is this possible?

On a related note, does a plugin exist for creating SOG and stemwall foundations?

medeek

I've got gable end trusses working for king post trusses:

I haven't made this latest update live just yet as I need to update all of the other truss types to make sure it does not break anything.

The other thing I am changing is the second user prompt box that allows one to enter in the number of trusses. I have now switched to a building length and the logic spaces the trusses based on the this length and the truss on center spacing. Gable end trusses can be switch on or off. Spacing of the gable studs is another user input.

juju

wow, this plugin is developing at an incredible rate, thanks!

For general designer use, I would think the plugin functions pretty well for now, personally I would shift focus to the positioning for now. Once that's sorted, move back into developing and expanding the truss configuration options.

medeek

I have a question or request for our Mac/Apple users. Has anyone tried using the plugin on a Mac. I don't have access to a Mac so I have no way of testing the plugin to see if it actually might work on this platform. If someone would be willing to test it out for me I have no problem in setting them up a permanent license and sending them the full version of the plugin, this would help me out a lot.

I've had to take a bit of a break from my coding, too much local work to process and never enough time in the day to get everything done.

As Juju suggests, I am going to try and figure out a better positioning mechanism before I start adding more truss types or additional features. This is the biggest thing holding the plugin back right now.

deaneau

@medeek

@unknownuser said:

Positioning: It would be really nice to drop the truss set right into place by clicking the location with the mouse.

could be this is usefull

SketchUp Extension Warehouse

Your library of custom third-party extensions created to optimize your SketchUp workflow.

(extensions.sketchup.com)

medeek

Version 1.0.7 - 11.03.2015
Trusses can now be positioned and sized via three mouse clicks, with the option for manual overide in the dialog windows.
The number of trusses is now based on the spacing and building length.
Floor trusses with top chord bearing now are positioned properly.

Hopefully I haven't broken the metric inputs with the latest revision. I will test further tonight but so far its looking really good.

medeek

Version 1.0.7 took a while to pop out. The big improvement is the ability to click with the mouse at three corners and place the truss set without any additional rotating or translating.

In literally seconds I can now put a floor and a roof on 4 walls using the truss plugin and the Homebuilder plugin:

Of course the gable walls are not quite right but you get the idea. I may have slightly misunderestimated (a word created by GW Bush) SketchUp and what one can do with it.

The biggest hurdle was to learn how to create and properly set up a "tool" within the API. Adding different truss types is much more fun than working through that mess.

I'm also thinking it might be useful to have an option to put sheathing on the roof and/or floor?

I'm also looking for a good plugin that does stemwall and slab on grade foundations, if anyone has recommendations please advise. I may use my own plugin for my own practice in order to quickly mock up certain structures and provide visuals. With the right tools I think SketchUp can be a very effective and quick turnaround platform

juju

thanks!

medeek

Version 1.0.8 - 11.04.2015

Added Weyerhauser TJI I-joists: 110, 210, 230, 360, 560, 560D.
Rim joist option enabled for TJI floor joists.

Only a rectangular configuration is available currently. If I can figure out how to code a polygon version of this that would be much more impressive (ie. pick the points that define the perimeter of the foundation and the plugin generates the complete floor layout).

This is straying a bit from trusses but I figured if I'm going to include floor trusses I might as well make floor joists available as well, just a small bit of code to get there.

driven

@medeek said:

...Has anyone tried using the plugin on a Mac...

I have tested a few version of the trial on mac running Yosemite...

PM me if you have specific questions or want me to test the latest version...

john

pbacot

haha--where's my comment? I was thinking of saying: add truss joist and solid lumber (as the floor trusses wouldn't be used on a lower floor like that). Then I thought you had enough to do! So I didn't post. Good work!

After years and years I still cannot get the programmer for another app I use to add engineered lumber options.

medeek

I'm considering adding the following advanced options to roof trusses:

1.) Sheathing
2.) Fascia
3.) Rake Board (Gable Overhang)
4.) Outlookers (Structural vs. Non- Structural, Horizontal vs. Vertical)
5.) Vent Blocks
6.) Gable End Trusses (Already in progress: Dropped top chord and structural variants)

This would then provide a fairly complete roof framing solution.

For floor trusses (adv. options):

1.) Sheathing
2.) Gable End Floor Truss (Ladders)
3.) Ribbon Board

For floor joists [TJI and dimensional lumber] (advanced options):

1.) Sheathing
2.) Midspan blocking at user selected bearing points.
3.) Sill Plate (for floor framing on top of concrete foundations)

Please suggest other options that might be handy to have.