[req] a good stairmaking plugin
-
-
rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.
-
@sdmitch said:
rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.
well which plugin r u using?
-
@rock1 said:
@sdmitch said:
rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.
well which plugin r u using?
-
@sdmitch said:
@rock1 said:
@sdmitch said:
rock, with a plugin of my own. I did cheat a little on the u-shaped 12,3,12 set. I created a run of 12 then copied,rotated and moved it into position. The run of 3 was then rotated and moved into place. The elliptical stairs required nothing additional to be done. The plugin has a u-shape option but it assumes stair runs stop and start at a landing.
well which plugin r u using?
don't mind but can you upload here?
-
I expect he would have uploaded it here already if he'd been interested in sharing with you.
-
Well Dave he never asked for it, only about it, so I fealt no compulsion the give it.
Rock, the plugin in question is attached. You can access it through the Plugins menu. There are 3 options, Normal, Spiral, and U-Shape.
Normal is just a straight run with a railing on one side. The steps are a group and the rail is a group.
Spiral is a circular or elliptical stair depending on the Max,Min width input. It is a single group.
U-Shape now accepts "turn steps" which replace the landing if defined. This is a single group also.
-
@sdmitch said:
Well Dave he never asked for it, only about it, so I fealt no compulsion the give it.
Rock, the plugin in question is attached. You can access it through the Plugins menu. There are 3 options, Normal, Spiral, and U-Shape.
Normal is just a straight run with a railing on one side. The steps are a group and the rail is a group.
Spiral is a circular or elliptical stair depending on the Max,Min width input. It is a single group.
U-Shape now accepts "turn steps" which replace the landing if defined. This is a single group also.
that's so kind of you , thanks a lot people like sdmitch are men of honour. Look fellas, these are men of honour, these are men of honour!! 
-
@sdmitch said:
Well Dave he never asked for it, only about it, so I fealt no compulsion the give it.
Rock, the plugin in question is attached. You can access it through the Plugins menu. There are 3 options, Normal, Spiral, and U-Shape.
Normal is just a straight run with a railing on one side. The steps are a group and the rail is a group.
Spiral is a circular or elliptical stair depending on the Max,Min width input. It is a single group.
U-Shape now accepts "turn steps" which replace the landing if defined. This is a single group also.
G'day Sam, nice little plugin!
I have some ideas for you to add if you could to extend it a little more.... see attached PDF.
-
Thank you very much Sam,
a very useful and time saving plugin.
Charly
-
Andrew, I will take a look at your suggestion and see what I can do. Some are trivial like asking for and using a given gap between the runs and the height and offset for the handrail. The "in-situ" option not so trivial but I'll see what I can do.
-
Thanks Sam, appreciate it!
Also for your u-shape stair maybe add a tread thickness and make treads components... Just helps with edits.
Well done, mate! simple and very effective tool! -
Andrew, I think I have incorporated all the changes you suggested except make the treads components. Maybe in version 3.
Advertisement