3D Truss Models

juju

If its not too much I will probably also specify two additional layers:

ceiling_gypsum
ceiling_batten

Ceilings aren't always made of gypsum board, I think we would need to consider an alternative name there? However, as long as the user is aware, this shouldn't pose a problem even if the naming stays as you proposed.

@medeek said:

What is the typical size for ceiling battens in your locale?

typically 38x38mm and 38x50mm is used, depending on truss spacings

@medeek said:

Also with a roof plane/extrusion, I see the necessity with having this addition when one uses battens but what about when there is already a sheathing layer on the roof and no battens?

I would still consider having the option there. Where I'm from, the typical roof construction does not use sheathing, I think I've used it once ever, with RheinZink as final roof material finish... Maybe some of the other people here can give us some feedback here?

medeek

On a similar note I would also like to create a new section in the global settings for "Sheathing". Here one can select whether sheathing will be an enabled advanced option by default or not and also other default parameters like sheathing thickness (wall and roof separately). My default sheathing material is OSB but in the global settings I will add a toggle between OSB and Plywood.

So far I have not dealt with wall sheathing on the gable ends, leaving it to the user to add their own but I would like to make that an option.

Also with the roof sheathing I would like make a global setting option of coloring the exterior/top face with a pre-determined roofing material if no other roofing extrusion is present, I've got to think about this some more.

My thinking is that the global settings should allow one to setup or customize the plugin so that all of your typical settings are "fine tuned" for you thereby minimizing the effort required when presented with all of the input menus during the roof creation process.

medeek

Another item I have been putting off is the heel blocking. I'm planning on offering two variants (vertical and angled), with the option to draw in the ventilation holes (typically 2" in diameter in my region, with 3 holes per 24" o/c spacing) if desired:

Obviously this is not a hot item since no one has bugged me about it but I have not forgotten it, just put it aside up until now.

With raised heels this may become a bit more complicated requiring more options, (ie. a V-cut instead of the typical bird holes). More input from builders would be useful in this regard.

With the angled heel blocking an overhang must be present for this to work so the code will revert to a vertical heel block when not enough overhang is present.

medeek

@Juju

I like what you have proposed here. What I will do is add a new section in the global settings called "Ceilings" that enables one to enable a gypsum wall board layer and/or battens. The thickness and sizes can also be set here as well (which become the default values) but the pop-up menu for ceiling - advanced options will allow for manual entry of each item and will also override the default values with the last values selected.

If its not too much I will probably also specify two additional layers:

ceiling_gypsum or ceiling_sheathing?
ceiling_batten

What is the typical size for ceiling battens in your locale? and the o/c spacing?

Also with a roof plane/extrusion, I see the necessity with having this addition when one uses battens but what about when there is already a sheathing layer on the roof and no battens?

medeek

I didn't particularly like the shade of the plywood material that is standard with SketchUp, so I went looking for a better texture. I think I've found one that I like but would be happy to entertain others if someone has a certain plywood material texture that they like.

medeek

I've got the plywood material working quite well in the plugin, and the ability to toggle between it and OSB in the global settings. I have a few more other features and edits and then maybe I will role a revision tomorrow or Sunday.

I actually like the plywood look much better than the OSB.

medeek

OSB or Plywood will now be an option for the floor sheathing:

The new sheathing tab in the global settings:

As time goes on I will probably add in more options for wall cladding and interior wall cladding (ie. gypsum) as well as the ceiling logic I discussed in a previous post.

I'm now working on the gable end wall sheathing option and the roof cladding option.

There are also two new options in the "General" tab which allow one to toggle the default setting for gable end trusses and advanced options (roof, floor etc...).

medeek

Version 1.8.0- 01.22.2017

Enabled roof cladding for common trusses.
Added nine "IKO Cambridge" architectural shingle colors into the roof cladding material library.
Added "plywood" material for roof and floor sheathing.
Added a "Sheathing" tab into the global settings.
Added entries in the "General" tab of the global settings to toggle default settings for gable end trusses and advanced options.

View model here:

3D Warehouse

3D Warehouse is a website of searchable, pre-made 3D models that works seamlessly with SketchUp.

(3dwarehouse.sketchup.com)

Initially I was just going to texture the exterior face of the sheathing for the roof cladding but then I realized that there may be cases where there is roof cladding but not sheathing or vice versa. In the end I went with a separate layer, material and extrusion for the roof cladding, this allows one to get more granular with the structure and in my mind closer to reality.

medeek

Trying to find a good wood shake or shingle roof texture, this one is pretty good except for a bit of banding:

Slipped in a wood shingle roof texture and a few metal ones in to Version 1.8.0.

I set the exposure of the wood shingles at 5-1/2", however it does look a little small to me, maybe 7-1/4" would be better?

medeek

When you first install the plugin the layers, materials and connector plates are disabled or turned off by default, maybe it would be better that they all be turned on. Either way all of these items can now be customized in the global settings.

medeek

I am wondering why SketchUp doesn't automatically ship with more high quality textures? This seems like a no-brainer.

juju

@medeek said:

I am wondering why SketchUp doesn't automatically ship with more high quality textures? This seems like a no-brainer.

Yup, you know it. I recently experienced a situation where people are starting to create rendering engine textures using 4K and higher images, this was over at Indigo Renderer. Crazy stuff but probably in the not-so-distant future normal.

medeek

And even if the quality is not so great a few more textures (built in) would be nice. I'm just surprised that there is not more built in textures for roof and siding materials. There should be at least 50-100 such textures (roof and siding specific) built in with SketchUp, or so I would think. This sort of thing could only help SketchUp's marketshare and adoption by serious architects and designers.

juju

Yes, more (and better) out-of-the-box textures will be great. However once "serious" professionals start using this for more than just conceptual study modeling, they generally get professional texture packs or collect / make their own.

medeek

Thinking about sheathing and cladding advanced option for the valley truss set. Typically the valley truss set is placed on top of the main roof sheathing:

View model here:

3D Warehouse

3D Warehouse is a website of searchable, pre-made 3D models that works seamlessly with SketchUp.

(3dwarehouse.sketchup.com)

If I create the sheathing and cladding just right then it will be easy for the user to manually trim the secondary roof sheathing and cladding with my trim tool and then optionally union them up with the built in Union tool. I may need to make a video showing exactly how to perform this task.

medeek

The valley truss set now has sheathing and cladding added as an option. You still have to manually trim the secondary roof's sheathing and cladding and then union it to the valley set's but with the trim tool this is very simple to do:

View model here:

3D Warehouse

3D Warehouse is a website of searchable, pre-made 3D models that works seamlessly with SketchUp.

(3dwarehouse.sketchup.com)

medeek

medeek

Call me crazy but I want to build something like this on my 10 acres so I can see all the way to the beach.

Given my wind speed (155mph ult.) and seismic zone (D2) I am probably looking at some serious holdowns at the first level (HDU 11). I would have to run the numbers but it would probably work. I would probably also sheath it with 5/8" plywood inside and out for some serious shearwall action, at least on the the first two floors. I would probably also frame the first two floor with DF No.2 2x8 studs or 2x6 studs at 12" o/c. I'm thinking spiral staircases between levels to save as much floor space as possible and to make it more interesting. Minimal windows on the first three levels and then the top level would have a lot of windows for the view. 11-7/8 TJI 210 for the floors with 3/4 sheathing T&G, 16" o/c.

The structure is 16'x16' with grade to top plate height of 38'8".

The roof is 6:12 pyramid hip with 2x8 rafters, I may go with a steeper pitch though.

On a structure like this overturning is a serious threat, I would need to check the dead weight of the structure and see if the seismic or wind forces could potentially lift the foundation right out of the ground. The solution is to increase the dead weight of the structure especially at the base, by upsizing the footing and stemwall. You will notice my stemwall is 10" thick, 36" deep and a 24"x12" footing, even this may not be enough.

Anyone design something goofy like this before. I don't know if my county building dept. would give it an approval though even if its engineered (stamped).

medeek

Since I have now have roof cladding enabled I figured it only made sense to have some sort of wall cladding enabled for the gable end walls:

The advanced options now allow one to specify wall cladding, the settings can be adjusted in the "sheathing" tab of the global settings. I currently only have 4 different colors of Hardiplank Siding but I will add more as requested and I can find textures that I like or create. It should also be noted that it isn't too hard to swap out the texture for the user's custom textures.

I'm also thinking about adding an option for an air gap between the wall sheathing and the wall cladding in the case that someone wants to use brick as their cladding option. For standard veneer brick in the US the air gap is usually 1" if my recollection is correct.

I will try to roll these latest additions into a new revision here shortly.

medeek

Version 1.8.1 - 01.29.2017

Enabled gable wall cladding for common trusses.
Added four "HARDIPLANK Cedarmill" siding colors into the wall cladding material library.
Enabled sheathing and cladding for valley truss sets.