Geomatry Resizer or Paramatric???
-
You can't resend them, they've already been sent, the recipients have not looked at them yet, that is what it means when PM's remain in the "outbox".
-
Hi Oscar,
Here's the original thread where this topic was discussed. I realize what I'm referring to in that thread is possibly a bit more involved than what you're trying to do... perhaps not.
but my idea outlined here will make someone some money if they set the right price.
I know someone wrote a script to do this (Gaeius linked me to it), but they wanted a thousand dollars for it or more... and what they need to ask is a reasonable price for it... like $80 or something... then perhaps everyone could actually use it... giving it an elitist price only stifles development - IMHO.
I really think your script has a lot of potential.
Is there a way you could make the selection of points or faces to lock into a graphically interactive tool instead of the awkward pull-down menu? (like how it works with the Subdivide and Smooth tool)
-
@unknownuser said:
Hi Bep,
May I know that do you receive my PM, please?
Oscar
Hi oscar,
As already posted to you in your PM-box, I instaled your test script succesfuly.
You should however have warned me about how great this script is.
I needed half an hour to get myself under control again.
Now my enthousiasme is somehow under control,I can give you some first, hopefully usefull remarks.
-Could you script preferbly use the users own units settings (my settings are Decimal, and cm for example.
-Could the defauld box to fill in when you want to adjust a line lenght be the size box.
(The most important for trilateration)
-If the first dimension of the sketcht triangle is changed, the hole figure should be scaled without losing the proportions of the initial sketch,like when scaling with the "tape measure"tool.
-The warning if you make size off a side of a triangle to large ,now is "the minimum size=..",
should it not be "max.size="?Now I am going to take a beer and play around with your skript for a while.
If some other remarks come up I will post them tomorow.Greetings,
Bep van Malde
-
I have been following this thread basically since it started, and am very interested in this ruby.
Have I missed the release of it for downloading or is it still under development?
thanks -
Hi Bep,
@bep said:
Now my enthousiasme is somehow under control,I can give you some first, hopefully usefull remarks.
-Could you script preferbly use the users own units settings (my settings are Decimal, and cm for example.
-If the first dimension of the sketcht triangle is changed, the hole figure should be scaled without losing the proportions of the initial sketch,like when scaling with the "tape measure"tool.
-The warning if you make size off a side of a triangle to large ,now is "the minimum size=..",
should it not be "max.size="?*units setting should be no problem.
*proportions of the initial sketch can be figure out.
*"max.size=" will be done.*Only I do not understand is :-
@bep said:
-Could the defauld box to fill in when you want to adjust a line lenght be the size box.
(The most important for trilateration)Thanks for your feedback
Oscar
Any feedback is welcome! -
@unknownuser said:
You can't resend them, they've already been sent, the recipients have not looked at them yet, that is what it means when PM's remain in the "outbox".
O I see!
Thank you! JujuOscar
-
*Only I do not understand is :-
@bep said:
-Could the defauld box to fill in when you want to adjust a line lenght be the size box.
(The most important for trilateration)Hi Oscar,
I just lookt at you post,and saw your question.
I attacht a picture to make clear what i mean.greetings Bep
-
@fletch said:
Here's the original thread where this topic was discussed. I realize what I'm referring to in that thread is possibly a bit more involved than what you're trying to do... perhaps not.
May I have a copy of the Building's program spreadsheet excel file, please ? (You can PM to me if you want.)
Thanks
Oscar -
Hi Fletch,
I have send you a PM to test.
Any feedback are welcome!Regards
Oscar -
Hi Fletch,
As we agree with this :-
@fletch said:
Really awesome, Oscar, yes, let's post this to the whole forum for all to share ideas. I would love a custom answer for the way our firm handles the excel spreadsheet program, but really probably it's best for everyone if it's more universal... as I mentioned.
but the fact you can read a spreadsheet from excel and draw spaces - that's really what I was looking to find out - and you did it!
Now, I have a format of it. Any feedback are welcome! I will do a quick script(spreadsheet to SU) for it.
Regards
Oscar
-
cool! looks like it has great potential!!!
you have 2 different fantastic tools going here now.
I think you will need to also attach your ruby that builds using your excel spreadsheet so people can test/understand/give feedback.
%(#BF4040)[actually using the .rbs file you had me test, I am unable to open the "Universal Format.xls" because after I gave it the location of the previous test file, that's all it will use.
So I am anxiously awaiting your script to test.]
-
Hi Fletch,
I will further modify the script for testing soon.
I am doing some CAD/CAM scripts for my CNC production.Sorry for you to keep waiting, give me some time, please!
Oscar
-
Hi,
This script is still under development? maybe another with this same 2D approach?
Thanks
Advertisement